Magic Chef Oven Parts

Light Bulb - 40W

11 Reviews

Part Number: 8009

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Range Bake Element

11 Reviews

Part Number: WPY04000066

The bake element is located on the bottom of the oven cavity. This spade-style bake element has push-on wire terminals and is 16 inches wide. It has a terminal depth of three inches and a total element length of nineteen inches. If your oven is not heating evenly, the element will not heat or has little to no heat when baking, you may need to replace the element. This genuine OEM bake element comes with instructions and is intended for use with electric ovens. Please remember to disconnect the power to your oven before you start your repair.

Flat Style Oven Igniter Kit

10 Reviews

Part Number: 12400035

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Long Oven Sensor

4 Reviews

Part Number: 12001656

The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you may need to replace the sensor. This long oven sensor kit comes with two harness adapters and is a genuine OEM part. Please remember to disconnect the power before starting your repair.

2 Piece Broiler Pan

2 Reviews

Part Number: 4396923

The broiler pan and insert allows you to cook on a stable surface while allowing the liquid to drain into the pan below, making clean up easier. The measurements for the pan set are 1-1/2-inch x 12-3/4-inch x 16-3/4-inch and is a genuine OEM part.

Glass Clip - Black

1 Review

Part Number: 7112P093-60

This clip helps to hold the exterior glass in place. Order quantity required.

Door Gasket

5 Reviews

Part Number: WPW10162384

The oven door gasket prevents heat from escaping the oven cavity when in use by creating a seal around the oven door. If your oven has little or no heat when baking, you may need to replace the gasket. This door gasket contains all the attaching clips needed for installation and is a genuine OEM part. Please make sure the oven is cool before installing the door gasket.

Door Glass Spacer

Part Number: 74003986

Sold individually.

Terminal Block

1 Review

Part Number: WPW10245259

The terminal block provides a way of connecting individual electrical wires and offers protection from electrical surges, voltages and currents. This part will also allow you to attach the power cord to the inner wiring of your range. If the terminal block has shorted out or the range is not getting the proper power, this part will need to be replaced. The nuts are not included with the terminal block, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power to the range before starting the repair.

Door Hinge

Part Number: 74001984

This door hinge is a genuine OEM replacement part for your wall oven. Replacing this part will require partially removing your oven from the wall, to access the hinge. This part contains one hinge, although it is recommended to replace both at the same time. You will need a Phillips screwdriver to unscrew the hing assembly and install the new one.