Maytag Washer Parts

Belt Kit

4 Reviews

Part Number: 12112425

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Washer Drive Pulley

1 Review

Part Number: W10721967

This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.

Spring Retaining Clip

Part Number: WP22001650

This spring retaining clip is used to hold the front panel onto the top of the washer. If your front panel is loose you might need to replace the clip. The clip is made entirely of metal and is used for some washing machines. This part is not quite an inch long and is sold individually. This is a genuine OEM part.

Hose Clamp

Part Number: WP596669

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Lid Switch

1 Review

Part Number: W10820036

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Adjustable Levelling Leg

Part Number: 22003428

The adjustable leveling leg is used to support and keep your washer level. If your washer shakes and moves during cycles you may need to replace the leveling leg. The stop nut is included with the leveling leg. The rubber foot is not included, it must be ordered separately. Order the quantity you need as they are sold individually. This is a genuine OEM part.

Heat Resistant Adhesive

Part Number: W10841140

This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.

Touch-Up Paint - White

4 Reviews

Part Number: 72017

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Suspension Spring

1 Review

Part Number: WP63907

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Hose Clamp

Part Number: WP285655

This single hose clamp is used to hold the water hose in place on the pump, to avoid the hose or pump from leaking water. If you notice your washer leaking you may need to replace the clamp. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.