25344753110 Kenmore Refrigerator Parts List

Air filter

The air filter helps the refrigerator eliminate odors by removing odor-causing particles. It is recommended to replace your air filter every 6 months to ensure maximum performance. This air filter measures approximately 7-inch wide by 5-inch deep, is black in color and is a genuine OEM part.

Refrigerator ice maker assembly (ice maker mold)

The ice maker assembly is used to produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4 pin wire harness adapter and tube. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Water inlet valve (water valve)

When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making or dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall. Make sure to disconnect both the water and power supply before starting your repair.

Defrost thermostat (thermostat)

The defrost thermostat snaps onto the top portion of the evaporator, it acts as a safety device and protects the evaporator from overheating during the defrost cycle. The thermostat can sense the rise in the evaporator temperature during the defrost cycle and cycles the defrost heater off after all the frost is melted from the coils. The defrost thermostat may need to be replaced if the appliance is experiencing temperature-related issues such as: too cold, too warm, frost buildup, not running, or running too long. This is a genuine OEM part. It is recommended to disconnect the power to your appliance before starting your repair.

Run capacitor - 120v (capacitor)

The run capacitor is attached to the compressor. This part is 120 volts and 15 mfd. The run capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Adjustable leveling foot - black (adjustable foot)

Sold Individually.

Fan motor evap 115v (motor)

The 115-volt evaporator fan motor is in the back of the freezer section and circulates air over the coils. These coils will convert the heat into cool air, which is then circulated. If your freezer is noisy or too warm from the motor not working, you will need to replace this part. It is suggested to replace the thermistor when replacing the evaporator fan. This is a genuine OEM part – note the screw holes in the motor are not threaded from the factory, use your old screws. Please remember to disconnect the power to the refrigerator before starting your repair.

Bin-door (door bin)

This door bin is for freezers. Door bin stores items in the door of the freezer. Follow the instructions in the owner's manual when installing this part.

Refrigerator freezer gasket (door gasket)

Hinge mounting hexagonal screw (screw)

Sold individually.

Drive gear (gear)

This icemaker drive gear works in conjunction with the ejector blades. The gear helps rotate the ejector arm to push the ice from the ice maker in to the ice bin. If your ice maker is not dispensing ice you may need to replace this part. The gear is little over an inch in diameter, white, and made of plastic. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Ice container (container)

Glass shelf insert (glass)

This drawer cover insert is for freezers. Drawer cover insert fits into the drawer cover frame and covers the drawer(s). Wear work gloves to protect your hands when installing this part.

Screw

Sold Individually.

Defrost heater

This part is located at the bottom of the evaporator. The defrost heater heats the evaporator in the defrost mode of operation to keep the cooling coils from frosting over. The thermostat must be replaced when replacing the defrost heater.