41729 Parts List

Door strike (striker)

This is a door strike for your washing machine. It is the piece that activates the door switch once the door is closed. If your washer will not start, will not fill with water, or the door will not open/close you may need to replace the door strike. This part is white in color, made from plastic, and measures approximately 2 1/2 inches. This is a genuine OEM part.

Washing machine drain pump (washing machine drain pump. If the washer does not drain then the drain pump may be clogged, damaged, or defective.)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Front load washer door lock and switch assembly (door lock and switch assembly)

Shock absorber kit (vibration/sh)

The shock absorber kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin, and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during its cycles. If one or both of them break or wear out it will cause the washer to vibrate or shake and will need to be replaced. This kit is a genuine OEM part. Please remember to disconnect the power to your appliance before starting the repair.

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Drain pump - 60hz 120v (water pump)

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

Magnetic door plunger (washer door magnet holder kit)

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

Control knob (knob-rotary)

The control knob is used to control the cycles for your dryer. This knob is white in color, made of plastic, 1 1/2” in diameter and accepts a D-shaped shaft. If the part is damaged, missing, or if the shaft is cracked, keeping you from turning the switch, you may need to replace the knob. This is a genuine OEM part and is sold individually.

Bearing,ball

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Gasket (washing machine tub seal. Located between the front outer tub and rear outer tub.)

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.

Door catch

This washer door catch is a replacement from the original. This is only available in black.

Door lock assembly (washer door lock latch assembly. The door lock secures the washer door shut during operation. Once the washing machine door is closed, the washer can)

Single spring with insulators (spring)

Detergent dispenser (box assembly, liquid detergent)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Water inlet valve (water valve)

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer will not stop filling with water, is leaking, or will not fill with water, you may need to replace the water inlet valve. Please make sure to disconnect the power to your washer before you start your repair. This water inlet valve is a genuine OEM part.