Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

48852 LG Washer Parts List

1-15 of 15

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:

EAP3527427

Availability:

In Stock

Price:

$20.15

Shock absorber kit

This kit includes 1 shock absorber and 2 pins.

Easy Part #:

EAP3522313

Availability:

In Stock

Price:

$28.12

Spider (rear flange (also called a spider) and shaft for washing machine drum. This part supports the dryer drum.)

The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long. If your washer moves or shakes, or sounds noisier than usual during the washing cycle, the support spider may be faulty or broken and should be replaced immediately.

Easy Part #:

EAP12075847

Availability:

In Stock

Price:

$194.60

Gasket (rear shaft seal at outer tub)

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

Easy Part #:

EAP3522854

Availability:

In Stock

Price:

$20.24

Locking pin (shock absorber locking pin)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Easy Part #:

EAP3523451

Availability:

On Order

Price:

$9.68

Easy Part #:

EAP3522860

Availability:

On Order

Price:

$17.83

Pump filter (washing machine filter and trap assembly.)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Easy Part #:

EAP3522306

Availability:

In Stock

Price:

$24.35

Easy Part #:

EAP3524025

Availability:

In Stock

Price:

$16.33

Easy Part #:

EAP3535199

Availability:

In Stock

Price:

$103.58

Washer motor rotor position sensor (rotor position sensor (rps))

The sensor monitors the direction and speed of the spinning rotor.

Easy Part #:

EAP11706506

Availability:

In Stock

Price:

$33.32

Easy Part #:

EAP3523351

Availability:

In Stock

Price:

$20.85

Easy Part #:

EAP3523348

Availability:

In Stock

Price:

$38.14

Easy Part #:

EAP3522949

Availability:

On Order

Price:

$208.06

1-15 of 15