6440A REV J Norge Washer Parts List

M series new style coil kit (sub 12001349)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Rear drum support roller kit (support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Crisper drawer cover (cover vegetable pan - wr32x10398)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.

Replacement ice maker (use wpl 4317943)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Flat style oven igniter kit (igniter-oven bake)

The flat style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, then your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter please be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3-3/4" in length and the amperage range is 3.3 to 3.6. The kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to the range wiring using porcelain wire nuts. This is a genuine OEM part.

Refrigerator ice and water filter (water filter - mwf)

Bake element - 220v 2300w (bake unit 208/240v)

This closed-hinged style bottom bake element is located on the bottom of the oven cavity to supply the heat for baking. This bake element has screw-on wire terminals is 18 1/4-inch wide and 14 1/2-inch deep to mounting flange and the terminal ends extend 2 1/2-inch past the flange. The element is 2300 watts and 20 volts. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Bake element - 240v (oven bake element. 240 volt 3100 watt element with screw style connections. If the oven does not bake then the element could have burned out.)

This 240-volt 3100 watt bake element has screw style connections, 13 1/4-inch wide by 163/4-inch long. The bake element is located on the bottom of the oven cavity and supplies the heat for baking. If your oven is not heating evenly, the element will not heat or there is little to no heat when baking, you may need to replace the element. This genuine OEM bake element comes with an instruction sheet and is intended for use with electric ovens. Please remember to disconnect the power to your range before you start your repair.

Evaporator fan motor

This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.

Belt drive

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Halogen light bulb - 120v 20w (lamp,halogen)

This clear 20-watt, 120-volt halogen light bulb is a replacement part for the bulb behind the top grill in your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open, or below the microwave to provide light for the cooking area. If the bulb in the microwave is burnt out or broken you will need to replace it. This is a genuine OEM halogen light bulb and is sold individually.

Felt trap duct (kit felpa e instrucciones)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Light bulb - 40w 130v (lamp oven 40w (special))

This 40 watt, 130-volt clear appliance light bulb is for your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open or below the microwave to provide light for the cooking area. It is clear in color and has a small screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.