6440A REV K Norge Washer Parts List

M series new style coil kit ('m' series boost/hold coil)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

D-shaped knob clip (dryer metal knob clip insert)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Rear drum support roller kit (support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Wheel & bushing ass (lower wheel and bracket)

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.

Bake element - 2600w 240v (elmnt-bake)

The 2600 watt 240 volts bake element is located inside the oven on the bottom to supply heat while baking. This closed hinged style bake element is 15 3/4-inch long 16 5/8-inch wide, terminal depth is 3-inch and they are 1 3/4 inches apart. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Replacement ice maker (icemaker)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Belt kit (washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement.)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Dishwasher upper dish rack wheel mount (wheel)

This part is located on the top dish rack with two per side. It is sold individually. This upper dish rack wheel mount can be used on either side of your dish rack. It is sold individually. The part includes the wheel and support, which attaches to the dish rack and allows it to slide in and out easily

Front drawer glide (front glide for oven drawer.)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Door catch kit (latch)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Upper roller and axle - kit of 4 (roller and stud asm (4pk))

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Middle spray arm kit

The middle wash arm rotates and distribute water inside the dishwasher. The kit has been redesigned and the supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube, and a screw. This kit does NOT include the upper support or mount. It must be ordered separately. This is a genuine OEM part. Please remember to shut off the water supply and disconnect power to your dishwasher before starting the repair.

Dryer heating element (heating element (11" long x 5" wide))

Upper rack wheel with mount (wheel)

This wheel and mount assembly is located on the upper dishwasher rack to allow you to slide the rack in and out easily. They are sold individually; four are usually required for your model. Also known as stationary wheel mount. This is a genuine OEM part.

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.