72059 LG Refrigerator Parts List

Handle screw (door handle mounting post)

This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.

Door basket assembly

Refrigerator door bin AAP73252202 is an original equipment manufacturer (OEM) part that fits some Kenmore Elite bottom-freezer refrigerators in the following series: 7957204, 7957205, 7957209, 7957218, 7957248, 7957311, 7957315, 7957401, 7957402, 7957404, 7957409, 7957504, 7957998 and 7957999. Also fits some LG bottom-freezer refrigerators in series LFX25991, LFX31925, LFX31935, LFX33975 and LMX31985. This door bin has an irregular shape?it's 13-1/2 inches wide, 9-1/2 inches deep on the left, 10-1/8 inches deep on the right and 4-1/4 inches tall. To install door bin AAP73252202, slide it into the door just above desired location and push down on the bin until it snaps into place.

Refrigerator door switch

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Refrigerator water filter (water filter)

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Plastic tube - 5/16 inch (tube,plastic)

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Basket assembly,door

Filter assembly,air cleaner (refrigerator compartment air filter. Should be replaced at least once a year to keep pesky odors at bay.)

Refrigerator Air Filters are a key component for neutralizing odors and ensuring a fresh stream of air into your refrigerator. Swapping your old filter out for a fresh one isn’t difficult and should take less than five minutes. This OEM filter measures approximately 3 inches (length) x 3 inches (height) x 5 inches (Depth). Air filters should be changed every 6 months depending on usage.

Ice maker assembly - 6 wire (ice maker kit)

NOTE: As per manufacture the secondary (smaller) wire connector has 6 wires in it. If original ice maker has 3 wire connector see part number PS7788172. Please verify connector before ordering.

Water inlet valve assembly (harness assembly)

This includes the primary and secondary valves along with the wire harness.

Door holder

This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.

Push button switch

This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light comes on. When you close the door the switch is pressed in, and the light turns off. You may need a putty knife to remove your old switch.

Left side connector rail

Spring,lever

Install part assembly,single (install part assembly,si)

Ice maker assembly - 3 wire (refrigerator icemaker assembly. Be aware the secondary or smaller wire connector has 3 wires in it. If original icemaker has a 6 wire connector see it)

NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.