75562 LG Dryer Parts List

1-15 of 101

Drum support roller and axle (dryer drum roller. If the dryer is noisy the roller may be worn and requires replacement. The bearing in the roller is self-lubricating so no grease i)

This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or is making loud squeaking noises, you may need to replace the drum support roller. It is recommended that you replace both rollers at once. This part is about 3 inches wide, comes with a bearing, roller shaft, and mounting clips. Sold Individually.

Easy Part #:

EAP8260240

Availability:

In Stock

Price:

$28.55

Dryer drum belt (dryer drum drive belt. 1/4 inch wide with 4 ribs and 3 grooves.)

The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum will not turn, then you may need to replace your belt. This drive belt is 1/4-inch wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Easy Part #:

EAP11705916

Availability:

In Stock

Price:

$17.08

Dryer lint filter assembly (dryer lint filter assembly with felt rim seal attached. Proper air flow is critical to dryer operation so the filter should be cleaned before every lo)

The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your current lint filter with this part. The frame of this line filter is made of white plastic, and the filter is sold individually. To replace the filter, simply remove the old, damaged filter, and replace it with the new one.

Easy Part #:

EAP3527575

Availability:

In Stock

Price:

$20.67

Sensor (dryer moisture sensor bar. If the dryer timer does not advance properly inspect the moisture sensor bars for damage which can cause the automatic dryi)

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.

Easy Part #:

EAP3529161

Availability:

In Stock

Price:

$6.02

Tub assembly,drum (dryer drum assembly)

This assembly is the tub, felt seal and 3 baffles in the tub.

Easy Part #:

EAP12579150

Availability:

No Longer Available

Blower thermostat (thermostat)

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.

Easy Part #:

EAP8747887

Availability:

In Stock

Price:

$12.07

Dryer thermistor ntc (dryer thermistor assembly with wire harness. If the thermistor is defective, it can prolong or shorten the drying time or cause a fault code.)

The thermistor, with wire harness, helps regulate and monitor the temperature inside of the dryer. The thermistor attaches onto the blower housing. If your dryer has a short drying time or a fault code is flashing, the thermistor maybe defective and will need to be replaced. Please remember to disconnect the power to the dryer before starting the repair. This is a genuine OEM part.

Easy Part #:

EAP3529026

Availability:

In Stock

Price:

$20.65

Thermostat (dryer high limit thermostat assembly. The thermostat has reset button in center it is trips due to poor air flow such as a clogged exhaust vent.)

This part is the replacement high-limit thermostat, or simply the thermostat for your dryer. It is approximately 2 inches wide from tip to tip. The center, rectangular portion of the thermostat is approximately 1 inch in width and a little more than 1 inch in length. The thermostat is a safety device that regulates the temperature inside the dryer. If the thermostat is shorted out, your dryer may not be getting any heat, and you will need to replace it. You can test the high limit thermostat for continuity by removing it and connecting it to a multimeter. Be sure to disconnect your dryer from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Easy Part #:

EAP3530484

Availability:

In Stock

Price:

$15.88

Clamp

The hose clamp works in conjunction with the water hose in the appliance by holding the water hose in place to keep the hose from leaking water on to the floor. If you notice your appliance leaking, you may have a crack in the hose or that the clamp is loose and will need to be replaced. The hose clamp is made of metal, measures approximately 1/2” in diameter and sold individually. This is a genuine OEM part.

Easy Part #:

EAP3524032

Availability:

In Stock

Price:

$3.42

Easy Part #:

EAP3530486

Availability:

In Stock

Price:

$14.03

Easy Part #:

EAP3523290

Availability:

In Stock

Price:

$172.74

Leg (dryer leveling leg)

This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer unit. Please note that this dryer leg is sold individually.

Easy Part #:

EAP3523560

Availability:

In Stock

Price:

$3.42

Easy Part #:

EAP3522851

Availability:

In Stock

Price:

$24.92

Easy Part #:

EAP3529308

Availability:

In Stock

Price:

$17.35

1-15 of 101