79090043600 Frigidaire Range Parts List

Drip bowl - 8" (8" drip pan)

The eight-inch drip bowl sits under the surface burner element to collect anything that may drip or spill over, to make cleaning up quick. This bowl measures approximately 10-inch in diameter at its widest point at the top. If your drip bowl becomes damaged or rusted it is best to replace the drip bowl to avoid any grease or spills from dripping down inside the range. This chrome drip bowl is compatible with most electric ranges that utilize plug-in surface burners. This is a genuine OEM part and is sold individually.

Chrome drip bowl - 6" (drip pan)

The 6-inch drip bowl sits under the burner to catch anything that may spill over to make cleaning up spills quick. This chrome drip bowl is compatible with electric ranges that utilize plug-in surface burners. This bowl measures approximately 8-inches in diameter. If your drip bowl becomes damaged or rusted it is best to replace the drip bowl to avoid any grease or spill from dripping down inside the range. This is a genuine OEM part and is sold individually.

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Front drawer glide (glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Terminal block kit (terminal block)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Infinite burner switch (infinite large element switch)

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Surface element - 8 inch - 220v (element)

The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need to replace this part if your element is not heating. It might have shorted out around the coil or the terminal block; you can test the coil to see if the burner or the switch may be at fault. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Surface element - 6 inch (element)

The standard Y-frame 6” surface element supplies heat to the cooking surface on your range and is a genuine OEM part. It has a black center medallion and looped terminal end. If your element is not heating, shorted out around the coil or if the terminal block shorted out and burnt out the contacts on the end, you may need to replace the element. Please be sure to disconnect the power to your range before starting your repair. Note: The manufacturer suggests replacing the receptacle at the same time.

Light bulb (bulb)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Oven rack

The metal chrome oven rack is a genuine OEM part. The oven rack is located inside of the oven cavity to provide a stable surface for cooking or broiling. This rack measures approximately 23” long x 16” wide and is sold individually. If your rack is rusted, damaged or missing you will need to replace the oven rack. No tools are required for this repair.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Indicator light lens (lens kit)

Probe

Note: Connector could be different than original. If so cut & splice wires together with porcelain wire nuts.

Bake element - 240v (element)

This bake element is found on the bottom of the oven.

Main terminal block kit (block)

This terminal block kit (also called terminal boards or strips) provides a convenient means of connecting individual electrical wires. This kit includes mounting screws and hex nuts and can be used with dryers and ranges. This kit allows you to attach the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.