79478 LG Dryer Parts List

Roller assembly (dryer drum roller. If the dryer is noisy the roller may be worn and requires replacement. The bearing in the roller is self-lubricating so no grease i)

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Dryer lint filter assembly (dryer lint filter assembly with felt rim seal attached. Proper air flow is critical to dryer operation so the filter should be cleaned before every lo)

The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your current lint filter with this part. The frame of this line filter is made of white plastic, and the filter is sold individually. To replace the filter, simply remove the old, damaged filter, and replace it with the new one.

Moisture sensor (dryer moisture sensor bar. If the dryer timer does not advance properly inspect the moisture sensor bars for damage which can cause the automatic dryi)

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.

High limit thermostat and thermistor kit (thermostat assembly)

The thermistor, with wire harness, helps regulate and monitor the temperature inside of the dryer. The thermistor attaches onto the blower housing. If your dryer has a short drying time or a fault code is flashing, the thermistor maybe defective and will need to be replaced. Please remember to disconnect the power to the dryer before starting the repair. This is a genuine OEM part.

Blower thermostat (thermostat)

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.

Cover,guide (guide cover)

Gas igniter (gas dryer igniter with bracket and wire harness. This is a round spiral-style igniter. The igniter uses heat to ignite the gas in the burner assembly.)

Comes with bracket and wire harness.

High limit thermostat (dryer high limit thermostat assembly. The thermostat has reset button in center it is trips due to poor air flow such as a clogged exhaust vent.)

This part is the replacement high-limit thermostat, or simply the thermostat for your dryer. It is approximately 2 inches wide from tip to tip. The center, rectangular portion of the thermostat is approximately 1 inch in width and a little more than 1 inch in length. The thermostat is a safety device that regulates the temperature inside the dryer. If the thermostat is shorted out, your dryer may not be getting any heat, and you will need to replace it. You can test the high limit thermostat for continuity by removing it and connecting it to a multimeter. Be sure to disconnect your dryer from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Parts assembly, svc (2 pack) (dryer drum roller assembly. Includes the roller shaft and mounting clips. As the bearing in the roller wears, it self-lubricates so no grease is neede)

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Felt seal (felt seal, dryer drum)

Baffle (lifter)

Pulley,idle (idler pulley wheel with bearing)

Parts assembly (lp conversion kit *note: Sticker indicating the gas type is not included.)

Switch assembly,safety

Valve assembly,gas (dryer gas burner valve assembly. Two solenoids. When installing the new valve, transfer the orifice from the old valve to the new valve.)