9888810 Hotpoint Range Parts List

Bake element - 220v 2300w (oven bake heating element with screw-on terminals. The element is 18-1/4 inches wide, 14-1/2 inches deep to mounting flange. Terminal ends extend 2-1/)

This closed-hinged style bottom bake element is located on the bottom of the oven cavity to supply the heat for baking. This bake element has screw-on wire terminals is 18 1/4-inch wide and 14 1/2-inch deep to mounting flange and the terminal ends extend 2 1/2-inch past the flange. The element is 2300 watts and 20 volts. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Infinite heat switch kit (stove top surface element control switch kit. If the surface element is not heating the element can be tested to determine if it is defective.)

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

Broil element (oven broiler heating element with screw-on terminals)

The broil element is located on the roof of the oven cavity to supply heat for broiling. The depth of the screw-on terminals is 2-3/4 inches and they are 1-1/4 inches apart. The mounting bracket is not included with the element. If the element is no longer heating or it has shorted out, then you will need to replace your broil element. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Terminal block (receptable kit (terminal block) for top surface element on electric range.)

This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.

Light cover (lamp cover assembly)

The oven bulb lens cover is made of glass and is approximately 2.75 inches in diameter. The lens cover protects the light bulb from being damaged. If the lens is cracked, damaged, or missing it will need to be replaced. It is suggested to make sure that the lens cover is cool to the touch before you start this repair. To remove the bulb lens cover simply slide the retaining clip off and then remove the lens. Replace it with a new cover and slide the retaining clip back on to hold it into place. This is an OEM part sourced from the manufacturer.

Drip bowl - 6" (chrome drip bowl for 6" burner, electric range)

This six inch chrome drip bowl is intended for use with looped terminal style surface mount burner element units.

Broiler pan - large (broiler pan grill kit, porcelain, includes grill and bottom pan)

The broiler pan and insert allows you to cook on a stable surface while allowing the liquid to drain into the pan below making clean up easier. This part is gray in color, made of enameled porcelain for an easy-to-clean, durable and made to last. The pan measures approximately 17” wide by 13” deep, insert measures 15 1/2” wide by 13” deep. This is a genuine OEM part.

Receptacle push-in (porcelain oven light socket)

This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.

Drip bowl - 8 inch (chrome drip bowl for 8" burner, electric range)

Sold individually.

Single microwave rack support (rack support)

Mounting screw (screw mtg)

This screw is less than 1/2 inch in length. It is sold individually.

Screw

Center piece - 6 inch burner (center trim for surface burner)

Bail (wire retainer for light lens)

Washer - 12 pack (washer, 12 pack)

This 12 pack of washers works in conjunction with your oven range. The washers are made of metal and measure approximately 0.5” in diameter. This is a genuine OEM part.