Parts for Kenmore Models A21

Belt kit (drive belt - 41.5 inches long)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Easy Part #:: EAP2005284

Availability:: In Stock

Price:: $37.07

Lid switch (switch, lid)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock

Price:: $22.04

Water inlet valve

This water inlet valve has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor. The water inlet valve controls the water flow into your washer. If your washer is leaking, will not fill with water, has no hot/cold water, or will not stop filling with water, you may need to replace the valve. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before you start the repair.

Easy Part #:: EAP1583805

Availability:: In Stock

Price:: $76.79

Mounting stem/tub seal kit (sub 22204012)

This tub seal helps prevent any leaking around the tub and the shaft of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:: EAP2351899

Availability:: No Longer Available

Rubber injector valve (sub 216201)

This rubber injector valve is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. This part helps control the water flow rate from the fill valve to the tub. If your washer is leaking you may need to replace this part. This injector valve is a genuine OEM part. Please remember to disconnect power to your washer before starting your repair.

Easy Part #:: EAP11738945

Availability:: In Stock

Price:: $19.84

Screw, 8/18 x 3/8 (screw)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $7.40

Drain pump (pump assembly)

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.

Easy Part #:: EAP11743017

Availability:: In Stock

Price:: $104.30

Screw (sub 910647)

This screw is half an inch long. It is made of metal and is intended for use with ranges, refrigerators, and washing machines.

Easy Part #:: EAP12349731

Availability:: In Stock

Price:: $19.34

Rubber foot pad

This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.

Easy Part #:: EAP11738859

Availability:: In Stock

Price:: $12.73

Hose clamp (clamp, hose)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:: EAP11743008

Availability:: In Stock

Price:: $6.64

Tub bearing kit (tub bearing repair kit)

The tub bearing kit is used on 2-belt washers. This part helps keep the interior tub spinning correctly. If your washer is leaking, noisy, or shakes and moves, you may need to replace the tub bearing. It is recommended to change the seal kit at the same time you are replacing the tub bearing. This is a genuine OEM part. Remember to disconnect the power and shut off the water supply to the washer before starting your repair.

Easy Part #:: EAP2347235

Availability:: In Stock

Price:: $45.80

Washing machine lid hinge ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Maytag brand washing machines.

Easy Part #:: EAP11738871

Availability:: In Stock

Price:: $10.37

Plastic injector nozzle

This injector nozzle is just under three inches long. It is white in color and made entirely of plastic.

Easy Part #:: EAP11738878

Availability:: In Stock

Price:: $9.63

Adjustable leveling leg (leg, adjustable (w/nu)

The adjustable leveling leg is used to support and keep your washer level. If your washer shakes and moves during cycles you may need to replace the leveling leg. The stop nut is included with the leveling leg. The rubber foot is not included, it must be ordered separately. Order the quantity you need as they are sold individually. This is a genuine OEM part.