CS0415 Parts List

Condenser fan motor kit (condenser fan motor kit. The part has been updated by the manufacturer and may not look like the orginal.)

This fan motor is used in frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, to cool the compressor and condenser coils. This fan motor also helps to evaporate excess water in the drain pan. This kit includes the motor, fan blade, wire harness, and screw. If your refrigerator/freezer section is too warm you may need to replace this part. This part has been updated by the manufacturer. It may look different in appearance but will still function the same as the original part. This is a genuine OEM part. Disconnect power to your refrigerator before starting the repair.

Affresh ice machine cleaner (affresh® cleaner for under counter ice machines)

This nickel-safe, unscented ice machine cleaner measures 16 fluid ounces and is used to remove mineral build-up and hard water and is compatible with several makes and models of freestanding ice machines. To use properly, turn off your ice machine and remove the existing ice left in your ice machine. Next, drain the water from your ice machine. Empty the entirety of this cleaner into the empty water pan and activate the cleaning cycle, and once the cycle is complete and you drain the pan again, the cleaning is complete!

Ice cutting grid wire (ice cutting grid wire. Includes 8 screws and approximately 10 feet of wire. 2 kits are needed to replace both directions.)

The wire kit attaches to the cutter grid frame. The wire is used to cut the ice slab into cubes. There is approximately 10 feet of wire. Note: 2 kits are needed to replace both directions. This is a genuine OEM kit. It is recommended to disconnect power to the appliance before starting the repair.

Ice cutter grid complete assembly (ice cutting grid)

This is an OEM part, sourced directly from the manufacturer. The cutter grid is located within the main unit of the ice maker and contains thin, heated wires that slice the ice into cubes that are then deposited in the ice bin. If the cutter grid is broken, ice can back up within the ice maker. This part is sold as a complete assembly and is used with freestanding ice makers.

Pump (recirculating pump)

The recirculation pump helps circulate the water over the evaporator to form ice that will be cut into cubes for standalone ice makers. If your ice maker is no longer making ice or there is no water flowing over the plate, you may need to replace the pump. This is a genuine OEM part. Please remember to disconnect power before starting your repair.

Water tube kit (1/4 inch plastic water line kit, approximately 72 inches. Tubing will need to be cut to match existing length.)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Water inlet valve (ice maker water inlet valve. 1/4" yellow inlet port. The water inlet valve supplies water to the ice machine. If the water inlet valve is defective, t)

This part has a 1/4" yellow inlet port.

Temperature sensor (water level sensor)

The temperature sensor is in the water pump area of the ice cube maker. This part helps to determine the water level in the water reservoir. Once the water reaches a certain level the temperature sensor will send a signal to the controls to fill the reservoir. This is a genuine OEM part. Please make sure you disconnect the power to the ice cube maker before starting your repair.

Door light switch (door switch)

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Screw

Sold individually.

Screw

Sold individually.

Pump (drain pump)

This drain pump is used in your ice maker. When you flush the reservoir on your ice maker to remove impurities, the drain pump is the part that removes the water from the reservoir. This is an authentic OEM part sourced directly from the manufacturer. Please remember to disconnect power to your refrigerator before making this repair.

Drain fastener cap (drain cap fastener)

Ice maker water distributor tube (water supply & distribution tube assembly)

The water distributor tube distributes water from the reservoir to the evaporator plate.

Evaporator thermistor (thermister, cube size control)

Used with free-standing ice cube makers.