Whirlpool Dryer Parts

Multi Rib Belt - 92-1/4"

36 Reviews

Part Number: 341241

This dryer drum belt has four ridges, three grooves, 1/4-inch wide and 92 1/4-inch long. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Dryer Thermal Fuse

9 Reviews

Part Number: WP3392519

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Roller Support Tri-Ring

Part Number: WPW10512946

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Door Catch Kit

7 Reviews

Part Number: 279570

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

M Series New Style Coil Kit

7 Reviews

Part Number: 279834

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Rear Drum Support Roller Kit

20 Reviews

Part Number: 349241T

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Dryer Drum Support Roller

2 Reviews

Part Number: WPW10314173

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Igniter Kit

7 Reviews

Part Number: 279311

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Leveling Foot

Part Number: 49621

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Dryer Repair Kit

12 Reviews

Part Number: 4392067

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.