Whirlpool Dryer Thermostats

Dryer Thermal Fuse

11 Reviews

Part Number: WP3392519

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Dryer Cycling Thermostat

4 Reviews

Part Number: WP3387134

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Thermal Cut-Off Kit

15 Reviews

Part Number: 279816

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Dryer High Limit Thermostat

3 Reviews

Part Number: WP3977767

The three-terminal high-limit thermostat with a terminal extension arm acts as a safety mechanism that keeps the dryer from overheating. When the dryer temperature reaches 221 degrees Fahrenheit, the thermostat will shut off power to the heating element until it drops by 80 degrees Fahrenheit. If your dryer has no heat, takes too long to dry or the thermostat has shorted out, you will need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Thermal Cut-Off Kit

6 Reviews

Part Number: 279769

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

High Limit Thermostat and Thermal Cut-Off Kit

Part Number: 279973

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

Thermal Cut-Off with High Limit Thermostat

Part Number: 280148

The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element.

Internal-Bias Thermostat

1 Review

Part Number: WP8318268

This thermostat has an internal heater L155-25F. This thermostat controls the internal drying temperature.

High Limit Thermostat

1 Review

Part Number: WP8557403

This authentic OEM high limit thermostat is made for your dryer. It is an important dyer element, because it will automatically shut off the heating element when it overheats. Be sure to disconnect the power to your dryer before you begin this repair.

Cycling Thermostat - Limit 135/155

Part Number: WP694674

Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.