General Electric Refrigerator PFS22SISBSS
Repairing your PFS22SISBSS General Electric Refrigerator is simple with official replacement parts made to fit your model. View a selection of popular parts, or review parts lists for each of the
PFS22SISBSS model diagrams below. Trust us to help you find the part you need and get your
PFS22SISBSS General Electric Refrigerator running again.
Diagrams for General Electric PFS22SISBSS Refrigerator
There are 5 diagrams for PFS22SISBSS. Click on the diagram where you think your part is located.
Most Popular PFS22SISBSS Parts
These are the most commonly purchased repair parts for PFS22SISBSS.
-
(2)
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.
-
(17)
This ice maker assembly is used to make ice in your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4-pin wire harness adapter, and a tube. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
-
(3)
The temperature sensor, also known as a thermistor, helps detect the temperature inside the refrigerator and sends the information to the control board. If your refrigerator is too warm or not cooling properly, you may need to replace the temperature sensor. This is a genuine OEM part. Please make sure to disconnect the power to the refrigerator before starting your repair.
-
(1)
This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep, 9.5-Inches high, and 5.25-Inches wide. It is certified to reduce particles, chlorine-resistant cysts, lead and five other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this, you?ll need to install a pressure-timing valve), and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns.
The installation is simple and does not require any tools or mess. To remove the old cartridge, turn it to the left and pull down carefully. Some water might drip, so keep a cloth handy. To install the new filter, place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically, and if it is a bottom-freezer model, it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light, reset it by pushing and holding it down for three seconds. If your model has a dispenser, run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.
-
The run capacitor is attached to the compressor and is 12 UF. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.
-
