LG Parts

Washing Machine Drain Pump and Motor Assembly

(17)

Part Number: 4681EA2001T

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Micro Switch

(2)

Part Number: 3B73362F

The microwave primary door switch, also known as a micro switch, is normally open. When the door is shut, the door switch will close to send power to the microwave to operate. If the microwave won’t start, then the switch has failed, and the part will need to be replaced. The micro switch is in the latch board section and monitors the position of the door. This part measures 1.5” L x .75” W NOTE: Due to the high voltage capacitor in the microwave, it can retain a lethal electrical charge, even when unplugged. It is suggested to have a service technician install the part. This is a genuine OEM part. Please disconnect the power to the microwave before beginning the repair.

Refrigerator Door Switch

(8)

Part Number: 6600JB1010A

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Water Inlet Valve - Hot

(5)

Part Number: 5220FR2006H

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Plastic Tube - 5/16 Inch

(5)

Part Number: MJU62070602

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Dryer Lint Filter

(11)

Part Number: ADQ56656401

The lint filter is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load. If your dryer takes too long to dry you may need to replace the filter. The lint filter is gray in color and measures approximately 12 inch wide by 11 inch high. The manufacturer has made an authorized substitution to the lint filter. Due to the changes, the manufacturer suggests changing the filter guide, part # MEA4905001 and filter cover, part # MCK66787901. This is a genuine OEM part.

FILTER,GREASE

(3)

Part Number: 5230W1A012E

Thermal Fuse

(3)

Part Number: 6931EL3003D

The high limit thermostat protects the dryer by shutting off the heating element when the dryer overheats. If the thermostat has blown, dryer won’t start or there is no heat, the thermostat will need to be replaced it can not be reset. If your dryer vent is clogged it could cause the thermostat to blow as well. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Refrigerator Water Filter

(1)

Part Number: AGF80300702

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Sensor

Part Number: 6500EL3001A

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.