Parts for Kenmore Models 10651252102

Filter inlet water tube (water tube)

As per the manufacturer, this part starts out as 1/4" tubing but ends up at 5/16".

Easy Part #:: EAP886401

Availability:: In Stock

Price:: $37.80

Water filter cap (filter cap)

This cap is biscuit in color.

Easy Part #:: EAP11739085

Availability:: In Stock

Price:: $11.92

Ice auger motor (motor)

This motor rotates the auger. When the auger rotates, it pushes ice out of the bin, through a chute to the user.

Easy Part #:: EAP11739700

Availability:: In Stock

Price:: $129.08

Spray paint - 12 oz. - white (spray)

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

Easy Part #:: EAP347819

Availability:: In Stock

Price:: $18.90

Screw

This screw is sold individually.

Easy Part #:: EAP11742755

Availability:: In Stock

Price:: $12.18

Flipper

This part is a replacement flipper or emitter cover for your refrigerator. It is made of white plastic and is approximately 3 inches by 2 inches. The flipper shields the emitter control board and houses the flipper cover for the emitter board. If your flipper is broken or missing, your ice maker may not make or dispense ice, and will need to be replaced. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Easy Part #:: EAP11739242

Availability:: In Stock

Price:: $32.67

Cycling thermostat (thermostat)

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.

Easy Part #:: EAP11743313

Availability:: In Stock

Price:: $53.34

Door light switch (light switch)

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Easy Part #:: EAP11738900

Availability:: In Stock

Price:: $26.83

Shelf support (stud assembly)

Sold individually.

Easy Part #:: EAP12578346

Availability:: In Stock

Price:: $13.11

Screw

Sold individually.

Easy Part #:: EAP11745619

Availability:: In Stock

Price:: $12.45

Single shelf stud (shelf stud)

This part screws into the side of the wall in your fresh food compartment and supports a shelf.

Easy Part #:: EAP11739228

Availability:: In Stock

Price:: $8.07

Light cover lens (light lens)

This part is used to cover up the light bulb.

Easy Part #:: EAP11739893

Availability:: No Longer Available

Screw

Sold individually.

Easy Part #:: EAP11742754

Availability:: In Stock

Price:: $7.37

Levers retainer/clip (clip)

This part is the replacement dispenser lever retainer for your refrigerator. It is made of metal and is approximately 2 inches long and ½ an inch wide. The bottom half of the dispenser lever retainer holds in the pivot points of the ice and water arms. If it breaks, the arms will be loose and can shake around. The top half springs the ice and water arms back into the original position, and if the retainer is broken, they will not be able to do this. The dispenser lever retainer is found behind the dispenser trim and can be removed with a ¼ inch nut driver. This part is sold individually and is an OEM part.