1068550580 Kenmore Refrigerator Parts List

Ice mold

This ice cube mold and heater assembly has a flake resistant surface with separations that mold eight ice crescents and is used with modular style icemakers on some refrigerators. The mold heater is an electrical device that thaws the ice quickly, so it can be released from the icemaker mold. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair.

Screw

Metallic screw that is less than an inch long. Does not include the plastic washer.

Water tube kit (water tube)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Arm-shut

Spray paint - 12 oz. - white (spray)

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

Cycling thermostat (thermostat)

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.

Door light switch (light switch)

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Screw

Sold individually.

Compression nut (nut-compre)

This single 1/4-inch compression nut is used to connect the lines that supply water to the correct components, the water dispenser and the ice maker, with the plastic water line of the icemaker assembly. This is a genuine OEM part. Please remember to disconnect the power and water supply to the refrigerator before starting your repair.

Refrigerator front roller kit (cabinet roller)

Support wheel assembly with bracket. Kit of 2.

Kickplate grille (grille)

This kickplate grille is attached to the bottom of the refrigerator.

Ice dispenser motor coupling (coupling)

This part attaches to the drive shaft of the ice dispenser motor.

Evaporator drip tray (tray)

This is the replacement evaporator drip tray for your refrigerator. It is made of white plastic and is approximately 19 inches by 9 inches. The evaporator drip tray sits below the evaporator to collect dripping water. If the drip tray is damaged, you may notice that your refrigerator is leaking. Because it is made of plastic, the drip tray can eventually develop a crack. You will need to pull out the refrigerator from the wall, and take off the bottom panel on the back of your refrigerator in order to access the drip tray for replacement. This is an OEM part sourced directly from the manufacturer.

Fresh food door gasket (door gasket)

This white door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.

Bottom kickplate clip (clip, grille)

This clip is sold individually.