Parts for Kenmore Models 11066814690

Dryer blower wheel (wheel, blower)

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.

Easy Part #:: EAP11743785

Availability:: In Stock

Price:: $30.92

Lid switch (switch, door)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock

Price:: $22.04

High limit thermostat (thermostat, 250 deg. F (121 deg. C))

With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 250 degrees Fahrenheit. The element will kick back in when the temperature drops to 190 degrees Fahrenheit. Differential of 60 degrees.

Easy Part #:: EAP11741441

Availability:: In Stock

Price:: $53.68

Screw, 8/18 x 3/8 (screw, 8a x 3/8)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $7.40

Dryer door switch actuator spring/lever (clip, door switch)

This black actuator spring with white rubber tip is used for both dryer doors and washer lids.

Easy Part #:: EAP11743767

Availability:: In Stock

Price:: $10.30

Lint trap housing seal (seal, bulkhead to lint chute)

This seal comes with the adhesive backing.

Easy Part #:: EAP11741506

Availability:: In Stock

Price:: $9.09

Two-piece split ring bearing (ring, bearing)

This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.

Easy Part #:: EAP334199

Availability:: In Stock

Price:: $48.83

Push-to-start switch - 2 terminal (switch, push-to-start)

This part is used to start the dryer once you have selected a setting on the timer.

Easy Part #:: EAP11741476

Availability:: On Order

Price:: $36.23

Drum roller shaft - left side (shaft, l.H.)

Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.

Easy Part #:: EAP11753706

Availability:: In Stock

Price:: $56.71

Rear drum seal kit (seal, rear drum)

This seal kit for large capacity gas and electric clothes dryers includes a seal, an adhesive, and an instructions sheet. This felt seal for the back of the drum is sewn with red thread.

Easy Part #:: EAP334194

Availability:: In Stock

Price:: $59.93

Seal (seal, lint chute)

This seal comes with the adhesive backing.

Easy Part #:: EAP12745423

Availability:: In Stock

Price:: $16.68

Seal and bearing (seal and bearing assembly)

This front panel seal kit doesn't include the plastic retainers, reuse the old retainers. No glue is needed, the seal stretches to fit.

Easy Part #:: EAP11773177

Availability:: In Stock

Price:: $43.64

Single front panel cip (clip)

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Easy Part #:: EAP11731288

Availability:: In Stock

Price:: $15.32

Cover screw (screw, 10-16 x 1/2)

Sold individually.

Easy Part #:: EAP11740701

Availability:: In Stock

Price:: $7.40

Drum support roller shaft - right side (shaft, r.H.)

Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.