Parts for Kenmore Models 11092964102

Hose clamp (clamp, hose)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:: EAP11743008

Availability:: In Stock

Price:: $6.64

Pump retainer (retainer, pump)

Sold Individually.

Easy Part #:: EAP11746362

Availability:: In Stock

Price:: $10.22

Tub wear pads - package of 3 (pad, base)

This package of pads contains three tub wear pads.

Easy Part #:: EAP334620

Availability:: In Stock

Price:: $15.68

Direct drive water pump (pump, complete)

This white direct drive drain pump is intended for use with washing machines that do not have belts. This pump has a backflow flapper valve, and two large ports for water to pass through.

Easy Part #:: EAP11741242

Availability:: In Stock

Price:: $54.72

Suspension spring retainer (retainer, suspension spring)

This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring retainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.

Easy Part #:: EAP11749057

Availability:: In Stock

Price:: $6.88

Drum support shaft - rear shaft with right hand threads (shaft, drum roller)

Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.

Easy Part #:: EAP11753708

Availability:: In Stock

Price:: $45.18

Agitator cam kit (cam driven)

This agitator cam kit contains an almost three inch white retainer and four agitator dog ears. This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).

Easy Part #:: EAP334624

Availability:: In Stock

Price:: $14.05

Clutch lining kit (band and lining (includes illus. 7 and 8))

This kit comes with springs, hardware, and brake lining.

Easy Part #:: EAP334642

Availability:: In Stock

Price:: $48.51

Blower wheel (wheel, blower harness (3))

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Easy Part #:: EAP11743811

Availability:: In Stock

Price:: $39.66

Screw (screw, 8-15 x 1/2)

Metallic screw that is less than an inch long. Does not include the plastic washer.

Easy Part #:: EAP11742721

Availability:: In Stock

Price:: $7.37

Tub-to-pump hose kit (hose, tub to pump (includes illus. 20))

This kit comes with the clamps.

Easy Part #:: EAP334685

Availability:: In Stock

Price:: $19.37

Lid hinge bearing (hinge, bearing (2))

This is the bearing for the lid hinge. Sold individually.

Easy Part #:: EAP11738874

Availability:: In Stock

Price:: $10.33

Single front panel cip (clip, front panel (2))

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.