36314039000 Kenmore Dishwasher Parts List

Push on nut (nut push on)

This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.

Hinge arm link (link hinge arm)

The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may be disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.

Drain solenoid kit (kit solenoid asm)

This kit includes the armature and linkage assembly.

Drain solenoid and bracket assembly (bracket & solenoid)

This valve opens in order for the water to drain out of the dishwasher.

Pump to wash arm rubber connector (connector pump asm)

This connector has female threads.

Sump housing (sump inlet)

This part is the replacement sump housing or sump insert for your dishwasher. It is made of plastic and is approximately 7 inches by 5 inches. The sump housing is attached to the bottom of the dishwasher tub and collects water for the pump. If your dishwasher is leaking, you may need to replace the sump housing. Be sure to disconnect the dishwasher from the water and power source before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Lower spray arm with tower (spray arm asm)

This part comes with a three section power tower spray nozzle.

Upper rack slide (rack slide)

This slide is mounted to each side of the upper cabinet wall. The dishrack wheels roll inside this track, which guides the upper rack.

Impeller and seal kit (wear ring base)

This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.

Detergent cup shaft and lever (shaft/handle det cup)

Cover is not included. Must order cover separately.

Door latch knob (knob, latch handle bk)

This knob is attached to the dishwasher door latch mechanism.

Drain hose (hose drain)

This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.

Detergent cup release arm (latch detergent cup)

This is the replacement detergent cup release arm for your dishwasher. It is made of black plastic and is sold individually. The detergent cup release arm is found on the inside of the dishwasher door, and it is the part that releases both the detergent and the rinse-aid. If the rinse-aid and detergent are not being released during the dishwasher cycle, or you notice that the release arm is cracked or damaged, then you will need to replace it. A damaged detergent cup release arm can also lead to a door latch failure on your dishwasher, and it may cause the dishwasher not to start. This is an OEM part sourced directly from the manufacturer.

Detergent cup cover (cover detergent cup)

Door latch kit (latch asm)

This door latch kit is used for dishwashers.