66515032K110 Kenmore Dishwasher Parts List

Cover screw (screw)

Sold individually.

Water inlet valve (valve-inlt)

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Spray paint - 12 oz. - white (spray)

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

High limit thermostat (thermostat)

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

Middle spray arm (spray arm)

This is a replacement middle spray arm in your dishwasher. You will find your middle spray arm mounted on the bottom of the middle dish rack. The upper spray arm rotates and sprays water during the operating cycle. If your dishes are not coming out of the dishwasher clean, you may have a malfunctioning middle spray arm. Debris and hard water buildup in your dishwasher can cause the middle spray arm to clog. To replace the spray arm, simply turn the arm counter clockwise to release it from the dish rack. Screw in the new spray arm to complete the repair. This part is sold individually.

Push-in retainer clip (retainer)

Sold individually.

Dishrack

Door latch - black (door latch)

NOTE: This part has been redesigned, it may appear different but will still function the same as the original.

Screw - 8-18 x 5/8 (screw #8-18)

Sold individually.

Inlet fill hose (fill hose)

This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, you will need a 1/4 inch nut driver, Channellock pliers, and a Phillips screwdriver. Replacing this part will require some disassembly, such as removing the water inlet valve from the fill hose, and the clamps which secure the hose in place. Reuse your existing clamps when securing your new fill hose in place.

Spring

This door spring is a genuine OEM replacement part for your dishwasher. The spring ensures that your dishwasher door does not fall open too quickly. If this occurs, one or both springs should be replaced. This part consists of one spring. To replace the spring, you will need to pull the dishwasher about six inches to a foot out from the cabinet. Replacing the spring has been rated as an easy repair by our customers.

Motor-pump (motor (also order 2 clamps w10169167 & 1 gromme...)

Motor

Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.

Kickplate - black (toe panel)

New Black Single Metal Access Panel Replacement Kit. Replaces old two part toe kick plates. Reuse insulation off old panel or see Recommended Parts.

Upper spray arm (spray arm)

The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To check your spray arm, make sure the spray arms can move evenly and freely on their bearing rings and mounting brackets. Remove your spray arm and check to ensure they are straight and undamaged. This spray arm is made of high-quality plastic and is just over 5 inches long.