YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Jenn-Air Refrigerator ruin your day. Repair your Refrigerator with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Jenn-Air Refrigerator parts to help you repair any of your home appliances.
Easy Part #:
In Stock - Ships Today
NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.
This screw is sold individually.
This part has a high-quality carbon filter that reduces contaminants. Replace the filter annually or when the filter light is on. Sold individually.
This metallic screw is less than an inch long and comes with a plastic washer.
This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.
This crisper drawer shelf support is used for many refrigerators.
This Whirlpool filter reduces taste and odor of clorine, small particulates, benzene, toxaphene, lead and mercury. It pushes in the botton front grille. Suggested replacement is every 6 months. Sold individually.
This screw is sold individually
This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
This part strips ice from the icemaker mold during the ejection cycle to prevent ice pieces from falling back into the mold.
Sold individually. This bulb is a 7 watt appliance incandescent light bulb.
In addition to the solenoid (115V), this kit also comes with a door strike and an ice door assembly. Please be advised the spring and roll pin are not included with this kit.
1/4" Plastic tubing, 8 1/2 feet long.
Use of this rivet requires a rivet tool.
This part may need to be cut-to-fit if it's too long for your appliance.
This defrost timer will cycle for twenty-one minutes after every ten hours of run time.
The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.
This part, when activated, releases water from the supply line into the ice mold.
Note: If the wall anchor that this piece mounts on is broken, then the support is needed. (Order per Model#)
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils.
These tube clamps are sold individually. The screw is not included.
NOTE: As per the manufacture the crisper drawer has been updated from the original. A new crisper cover may need to be purchased for the drawers to work.
This part connects the ice auger to the motor through the bin.
This part allows the refrigerator to go into defrost mode only when required.
This Puri-Clean water filter will fit most Maytag and Jenn Air refrigerators that have a screw-in filter. Sold individually.
Used with Evaporator Fan Motors.
This part helps with the closing of the door and helps keep them in position.
The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against excessive temperatures.
Holds the ice when it's released by the icemaker.
Long harness thermistor kit.
When the icemaker shut off arm is high enought the ice maker will shut off and no more ice will be made until the level of the ice in the bin drops. Also the ice maker can be turned off by lifting the arm all the way to the top until in a locked position.