YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken KitchenAid appliance ruin your day. Repair your appliance with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all KitchenAid appliance parts to help you repair any of your home appliances.
Easy Part #:
In Stock - Ships Today
This metallic screw is less than an inch long and comes with a plastic washer.
This part has been redesigned and now comes in a kit. This kit includes 2 adjuster assemblies, 1 left hand and 1 right hand actuator cover, 2 gray adjuster covers, and 2 gray adjuster housings.
This Whirlpool filter reduces taste and odor of clorine, small particulates, benzene, toxaphene, lead and mercury. It pushes in the botton front grille. Suggested replacement is every 6 months. Sold individually.
This door closing cam is located on the bottom of the fridge/freezer.
This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.
This kit includes 2 door balance links and 2 door balance mounts with wheels.
This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.
***NOTE: Ice maker does NOT come with the bail or shut off arms. Must order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. Its harness can be reused. The ice maker will not fit refrigerators that have the ice auger mounted on the door.
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
This part has a closed cast motor housing. The sump housing is sold separately.
This screw is sold individually.
This ice guide is located in the freezer door.
This filter is mounted in the bottom grille. Sold individually.
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.
This dryer door latch kit comes with one plastic door latch and one metal door strike.
The bulb is sold separately.
Used with Evaporator Fan Motors.
This white ice bin auger drum comes with a washer.
The humidity control allows you to adjust the humidity within the crisper. This can extend the life of the vegetables/fruit.
Sold individually. Each roller holds two wheels. There are four sets that attached to the lower rack.
This kit has been redesigned. The supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube and a screw. This kit does NOT include the upper support or mount.
This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.
NOTE: This part is no longer available in white or biscuit.
If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.
The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold.
Note: This valve has been updated by the manufacturer and NO longer includes the removable pre-filter bracket connector. Must be ordered separately on PS3502196
This bracket holds the micro switches and the light in the freezer dispenser section.
This ten watt appliance light bulb is used with both washers and dryers. Sold individually.
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
This kit includes the motor, fan blade, wire harness and screws.
NOTE: The manufacturer has changed the product to appear different than the original, but will still function the same as the original part. It is an OEM factory replacement.
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
This is a 12 piece kit.