DDC0580BAL GE Dryer Parts List

D-shaped knob clip (metal insert for dryer control knob.)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Rear drum bearing kit (rear drum bearing kit. *bearing plate has slot in it for ground strap. The drum bearing supports the rear of the dryer drum. Over time, the drum beari)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Drive belt (dryer drive belt. This is the most common GE/Hotpoint dryer belt. 87" long and 1/4" wide. 4 ridges.The drive belt dries out over time.)

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Lint filter with frame (dryer lint filter. This filter should be cleaned before every load to ensure proper airflow. If the lint filter is torn or damaged, replace it.)

The lint filter and frame for your dryer traps unwanted lint and debris so your dryer can effectively dry your clothes. If the old lint filter is cracked or clogged, or the dryer takes too long to dry or if excessive lint is accumulating inside the dryer or its venting, you may need to replace the lint filter. To replace the filter, simply remove the old, damaged filter, and replace it with the new one. This part is approximately 13 inches by 3 inches.

Door latch (dryer door catch kit)

This part helps to keep the door closed while the machine is running.

Rear drum bearing (rear dryer drum bearing. Be sure to enter your model number to ensure that you have the right bearing for your model.)

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

Front drum slide kit (front drum supports/glides (2), with hardware)

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Idler pulley wheel (idler pulley wheel with spacer and retainer clip)

This white idler pulley is used for many clothes dryers. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Screw

This screw is sold individually.

Heater 2-coil restring kit - 240v (heating element kit, includes two coils and hardware, 240 volts)

This restring coil kit is used to replace the existing coil in a dryer's heating element.

Drive motor

Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.

High limit thermostat (high limit thermostat, l258-50f)

With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device, will kick back in when the temperature drops to 210 degrees Fahrenheit. (Limit: 260-50)

Cycling thermostat - limit: 145-15 (dryer thermostat assembly, l145-15)

It has a limit of 145 degrees Fahrenheit and a differential of 15 degrees. This means that with this thermostat, your dryer's heating element will cut out at 145 degrees Fahrenheit and kick back in when the dryer's internal temperature drops by 15 degrees.

Clamp& screw (clamp & screw kit for blower wheel)

Timer knob (timer knob, chrome and black, 1ea.)

This knob accepts a D-shaped shaft.