Parts for Kenmore Models 1069631680

Icemaker control assembly (motor mold)

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. It also controls the heater, the water inlet valve, the cube size, and cube ejection. The control assembly is located under the white cover of the ice maker. If the ice maker is making too much ice or not making ice at all, you may need to replace the control assembly. The motor is not sold separately. This is a genuine OEM part. Please make sure you disconnect power to the refrigerator before starting your repair.

Easy Part #:: EAP2341896

Availability:: In Stock

Price:: $80.09

Condenser fan motor kit (motor kit)

This condenser fan motor is used with frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, cooling the compressor and condenser coils. This part also helps to evaporate excess water in the drain pan. If your refrigerator/freezer section is too warm you may need to replace this part. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting the repair.

Easy Part #:: EAP395284

Availability:: In Stock

Price:: $58.77

Capacitor (production capacitor)

The run capacitor is attached to the compressor. This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Easy Part #:: EAP11757023

Availability:: In Stock

Price:: $51.01

Refrigerator single water inlet valve (inlet valve)

The single water inlet valve is used to supply water to the water dispenser and the ice maker. The valve is 60Hz 120 Volts and 35 watts. If your ice maker isn’t producing ice or the water dispenser not dispensing water, the solenoid might have gone bad and will need to be replaced. This valve includes 1/4” tubing and a plastic union. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the refrigerator before starting the repair.

Easy Part #:: EAP11740365

Availability:: In Stock

Price:: $48.09

Door shelf end cap set (endcap trim)

This door shelf end cap set contains two white end caps. Each end cap can be used as either the right or the left side. These end caps also come with adhesive strips and an instructions sheet.

Easy Part #:: EAP370794

Availability:: In Stock

Price:: $17.00

Refrigerator door switch (light switch)

Door switch turns the light off when you close the door.

Easy Part #:: EAP12728638

Availability:: In Stock

Price:: $32.07

Ice maker water fill tube kit (fitting)

The ice maker fill tube is used to supply water to the ice maker during the fill cycle and is located in the back wall of your refrigerator/freezer. The fill tube is 10-inches long and includes a compression nut and a tube insert. If the fill tube is cracked or leaking water you will need to replace it. This part is white in color, made of plastic, and is a genuine OEM part. Please remember to disconnect the power and shut off the water supply before starting your repair.

Easy Part #:: EAP11739222

Availability:: In Stock

Price:: $9.44

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Easy Part #:: EAP385132

Availability:: In Stock

Price:: $7.07

Bimetal defrost thermostat (bimetl-def)

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

Easy Part #:: EAP11742474

Availability:: In Stock

Price:: $38.80

Screw

Sold individually.

Easy Part #:: EAP11742744

Availability:: In Stock

Price:: $7.40

Add-on icemaker assembly (icemaker)

This icemaker kit comes with a flat plug, wiring harness, fill tube, water inlet valve, ice bin, mounting hardware, and instructions.

Easy Part #:: EAP317560

Availability:: In Stock

Price:: $79.85

Ice mold

This ice cube mold and heater assembly has a flake resistant surface with separations that mold eight ice crescents and is used with modular style icemakers on some refrigerators. The mold heater is an electrical device that thaws the ice quickly, so it can be released from the icemaker mold. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair.

Easy Part #:: EAP11749915

Availability:: On Order

Price:: $129.08

Water fill cup and bearing (fill cup)

The ice maker fill cup and bearing dispenses the water into the ice mold during the fill cycle. If your ice maker is not making ice, is leaking, or the cup or bearing is cracked, you will need to replace this part. This part is three inches long, white in color, and is made of plastic. It is a genuine OEM part. Please remember to disconnect the power and water supply to your refrigerator before starting the repair.

Easy Part #:: EAP11743318

Availability:: In Stock

Price:: $33.67

Screw

Metallic screw that is less than an inch long. Does not include the plastic washer.

Easy Part #:: EAP11742721

Availability:: In Stock

Price:: $7.37

Water tube kit (water tube)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.