Parts for Kenmore Models 1107109710

Door catch kit (catch assembly)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $4.02

Water inlet valve with mounting bracket (valve assembly)

The water fill valve kit attaches the water lines on the back of your washer. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. This kit includes a blue body fill valve, a mounting bracket and a screw. The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Easy Part #:: EAP334646

Availability:: In Stock

Price:: $32.08

Igniter kit (ignitor)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $34.93

Dryer radiant flame sensor (sensor radiant)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $41.69

Lid switch (switch, door)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock

Price:: $22.04

Screw, 8/18 x 3/8 (screw, 8-18 x 3/8)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $7.40

Dryer door switch actuator spring/lever (lever, door switch)

This black actuator spring with white rubber tip is used for both dryer doors and washer lids.

Easy Part #:: EAP11743767

Availability:: In Stock

Price:: $10.30

Cycling thermostat - limit 135/155 (thermostat-cool down)

Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.

Easy Part #:: EAP11743793

Availability:: In Stock

Price:: $49.43

Hose clamp (clamp)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:: EAP11743008

Availability:: In Stock

Price:: $6.64

Front top lock (lock, top)

This part is used to secure the top panel to the cabinet. Sold individually.

Easy Part #:: EAP11738705

Availability:: In Stock

Price:: $12.28

Hose clamp (clamp)

This single hose clamp is used to hold the water hose in place on the pump, to avoid the hose or pump from leaking water. If you notice your washer leaking you may need to replace the clamp. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.