Parts for Kenmore Models 11074410200

Water inlet valve with mounting bracket (valve, water mixing)

The water fill valve kit attaches the water lines on the back of your washer. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. This kit includes a blue body fill valve, a mounting bracket and a screw. The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Easy Part #:: EAP334646

Availability:: In Stock - Ships Today

Price:: $32.08

Centerpost gasket (gasket, center post)

Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.

Easy Part #:: EAP11723081

Availability:: In Stock - Ships Today

Price:: $5.37

Lid switch (switch (alt.))

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock - Ships Today

Price:: $22.04

Hose clamp (clamp, hose)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:: EAP11743008

Availability:: In Stock - Ships Today

Price:: $6.64

Hose clamp (clamp)

This single hose clamp is used to hold the water hose in place on the pump, to avoid the hose or pump from leaking water. If you notice your washer leaking you may need to replace the clamp. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Easy Part #:: EAP11740613

Availability:: In Stock - Ships Today

Price:: $10.33

Washer transmission stem seal (seal)

Sold individually.

Easy Part #:: EAP11746747

Availability:: In Stock - Ships Today

Price:: $10.33

Inlet hose - 5 ft (hose, inlet)

This hose can handle hot or cold water and is five feet long.

Easy Part #:: EAP11746820

Availability:: In Stock - Ships Today

Price:: $19.27

Screw (screw, 10-16 x 1/2 (standard hardware item-may be purchased locally))

This screw is sold individually.

Easy Part #:: EAP11743744

Availability:: In Stock - Ships Today

Price:: $7.23

Water inlet hose washer (washer, 1-1/16 x 5/8 (standard hardware item-may be purchased locally))

The washer is black in color and works in conjunction with the fill hose in your washer. This washer helps by creating a watertight seal to avoid leaking. Over time the washer may be worn down or damaged which will allow water to pass through and start leaking and will need to be replaced. This part measures 1-1/16” x 5/8” and is made of rubber. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11738697

Availability:: In Stock - Ships Today

Price:: $7.40

Hose clamp (clamp, hose)

The hose clamp helps secure the hose in place on the pump to avoid the pump or hose from leaking water onto your floor. If you notice your appliance leaking you may have a crack in the hose or the clamp is loose and will need to be replaced. This part is made of metal, measures approximately 2” in diameter and sold individually. This is a genuine OEM part.