Parts for Kenmore Models 11087379330

Dryer thermal fuse (fuse, thermal)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Easy Part #:: EAP11741460

Availability:: In Stock

Price:: $18.27

Light bulb - 40w (bulb, dryer drum)

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Easy Part #:: EAP884734

Availability:: In Stock

Price:: $9.16

M series new style coil kit (coil, 60 hz. (2 terminal) (main))

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $26.40

Rear drum support roller kit (roller, support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP347627

Availability:: In Stock

Price:: $13.37

Door catch kit (strike, door)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $4.02

Igniter kit (ignitor, burner 686590 (alt.))

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $34.93

Idler pulley assembly (idler, & pulley)

The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11743765

Availability:: In Stock

Price:: $16.41

Drive motor with pulley (motor, 60 hz.)

This drive motor operates the dryer by turning the drive belt which spins the drum and will fit most Whirlpool incorporated dryer brands before 1996. If the motor has shorted out, it will no longer turn the drum and will need to be replaced. The drive motor includes the pulley that is not available separately. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334304

Availability:: In Stock

Price:: $94.73

Roller support tri-ring (ring, tri)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock

Price:: $10.54

Dryer lint filter and cover (cover, lint screen)

Cover and filter as an assembly. It is used in dryer, If the lint filter cover is damaged or cracked, it should be replaced.

Easy Part #:: EAP11726200

Availability:: In Stock

Price:: $50.64

Dryer radiant flame sensor (sensor, radiant)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $41.69

Lid switch (switch, door)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.