Parts for Kenmore Models 11087983830

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $24.12

Rear drum support roller kit (roller, support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP347627

Availability:: In Stock

Price:: $13.53

Door catch kit (strike, door)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $4.06

Idler pulley (pulley assembly)

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:: EAP334244

Availability:: In Stock

Price:: $23.70

Multi rib belt (belt, drive)

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

Easy Part #:: EAP382430

Availability:: In Stock

Price:: $20.66

Lint filter (lint, screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:: EAP1491676

Availability:: In Stock

Price:: $57.83

Drive motor with pulley (switch, motor)

This drive motor operates the dryer by turning the drive belt which spins the drum and will fit most Whirlpool incorporated dryer brands before 1996. If the motor has shorted out, it will no longer turn the drum and will need to be replaced. The drive motor includes the pulley that is not available separately. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334304

Availability:: In Stock

Price:: $95.83

Leveling foot (foot, dryer (plastic) (4))

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:: EAP1609293

Availability:: In Stock

Price:: $7.69

Roller support tri-ring (tri ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock

Price:: $10.66

Thrust washer (washer, thrust)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock

Price:: $7.49

Dryer radiant flame sensor (sensor, radiant)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $42.18

Disposable thermal fuse - two terminal (thermal fuse)

This part attaches to the exhaust duct of your clothes dryer.

Easy Part #:: EAP11741444

Availability:: In Stock

Price:: $16.92

Idler pulley with bracket (idler bracket)

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Easy Part #:: EAP11726337

Availability:: In Stock

Price:: $22.52

Lid switch (switch, door)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock

Price:: $22.30

Moisture sensor (electrode, sensor)

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.