Parts for Kenmore Models 11092966101

Agitator directional cogs (dog, agitator (4))

These agitator directional cogs are commonly referred to as dog ears. They come four in a package and are usually used with direct drive washing machines. When the teeth on the outer edge are worn down the cogs will not engage with the upper agitator, causing it not to agitate properly. It is recommended to replace all four at the same time. These agitator directional cogs are ?-inch high and 1-inchlong and they are a genuine OEM part.

Easy Part #:: EAP388034

Availability:: In Stock

Price:: $4.09

Direct drive motor coupling (coupling, motor and isolating)

The newer version of the coupler kit is made with new metal sleeves for added strength. This part is located between the motor and transmission on the direct drive washer that does not have a belt. The coupler will break to protect the motor from damage if the drive motor system seizes up. If your washer will not fill, will not agitate or spin, but it will drain the water from the tub, you may need to replace this part because it has failed. This is a genuine OEM part. Disconnect the power to your washer before starting the repair.

Easy Part #:: EAP1485646

Availability:: In Stock

Price:: $23.27

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $23.85

Door catch kit (strike, panel)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $4.02

Suspension spring (spring, suspension (3))

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Easy Part #:: EAP11743345

Availability:: In Stock

Price:: $7.07

Dryer drum support roller (support, roller)

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Easy Part #:: EAP11752609

Availability:: In Stock

Price:: $19.40

Clutch assembly (clutch (complete))

The clutch assembly is used on direct drive washing machines and helps spin the basket during the spin cycle to remove water from the tub. If your clutch is worn out it can cause the washer to be noisy or leave water in the tub because it won’t drain properly, which will leave your clothes soaked. The clutch assembly includes a brake cam driver, retaining ring, bearing, and a spring, depending on your model number. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the washer before starting your repair.

Easy Part #:: EAP334641

Availability:: In Stock

Price:: $22.09

Idler pulley (pulley, idler)

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:: EAP334244

Availability:: In Stock

Price:: $23.43

Multi rib belt (belt, drive)

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

Easy Part #:: EAP382430

Availability:: In Stock

Price:: $20.42

Thermal cut-off kit (thermal cutoff)

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

Easy Part #:: EAP334278

Availability:: In Stock

Price:: $40.19

Roller support tri-ring (tri-ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock

Price:: $10.54

Thrust washer (washer, thrust)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock

Price:: $7.40

Agitator bolt (screw)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Easy Part #:: EAP11741866

Availability:: In Stock

Price:: $6.56

Tub spring (spring, counterweight)

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be noisy and off balance during the spin cycle. Please check your model to see how many springs are required for your model. The spring is sold individually. This is a genuine OEM part. Please make sure you disconnect the power to the washer before starting your repair.