3638799610 Kenmore Refrigerator Parts List

Ice maker (spring)

This ice maker assembly is used to make ice in your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4-pin wire harness adapter, and a tube. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Single outlet valve kit (water valve)

When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making/dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall and make sure to disconnect both the water and power supply before starting your repair. As per the manufacturer, this valve has a new quick connection. You must cut the retaining nut off your current plastic water line, and gently push it into the new valve.

Defrost timer - 120v 60hz (defrost control)

The defrost timer acts like a clock, continually advances and alternates between activating the cooling cycle and the defrost heater. This 120V 60Hz defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange. If your refrigerator is too warm, freezer section is too warm, freezer is not defrosting, or leaking, you may need to replace the defrost timer. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Fresh food door gasket (gasket door ff)

This fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.

Ice bucket - white (bucket ice)

The ice container is used to store the ice cubes that have been released from the ice maker in the freezer section until ready to be used. If the container becomes cracked or lost, you will need to replace the container. The container is white in color, made of plastic and measures approximately 12”L x 10”W. This is a genuine OEM part.

Condenser fan motor - 115v (motor cond fan)

This part comes with 3 round pin connection terminals. This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

Evaporator fan blade kit (ring fan blade)

Sheet metal screws - 12 per pack (screw)

This is a replacement pack of sheet metal screws for your refrigerator. These are Phillips-head screws, and are approximately ¾ of an inch long. This package contains 12 screws. These screws are typically used to attach your refrigerator or freezer door handles to the door. These screws are OEM parts sourced directly from the manufacturer.

Freezer door gasket (gasket door fz)

This white door gasket is used to seal the freezer door when closed.

Evaporator fan motor kit (evap. Fan motor)

This evaporator fan motor operates in a counter clockwise fashion. This motor's shaft is 3/8 of an inch and the motor has two right side terminals. NOTE: Harness wires NO longer come with the part.

1/4 tubing nut (nut & sleeve 1/4")

Screws - package of 12 (screw)

This is a package of twelve replacement screws. They are designed as replacement screws for refrigerators. Be sure to check that your appliance model is compatible with these screws. The screws are approximately ¾ of an inch in length.

Drawer slide rail - right side (slide mt. Pan rh)

Defrost heater kit (defrost heater)

This kit comes with the heater, wires and crimp-style connectors.

Icemaker stripper (stripper)

This part strips the ice from the icemaker mold during the ejection cycle.