41790862992 Parts List

1-15 of 199

Drum support bearing (bearing-drum support)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP418807

Availability:

In Stock

Price:

$4.35

Drum glide - white (glide-drum)

The white drum glide supports the drum on the front side and helps rotate smoothly and quietly while operating. If your dryer won’t tumble or is noisy, the drum glide may be worn down causing a metal on metal noise. Your dryer requires two glides; it is recommended to replace both glides at the same time. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:

EAP5574052

Availability:

In Stock

Price:

$20.87

Dryer lint screen (trap-lint)

This dryer lint screen (part number 5304516871) is for laundry centers. Dryer lint screen 5304516871 captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.

Easy Part #:

EAP12585473

Availability:

In Stock

Price:

$27.80

Drive v-belt (belt-washer)

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum will not agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Easy Part #:

EAP1146950

Availability:

In Stock

Price:

$14.81

Drain pump - 120v 60 hz. (pump-drain-wshr/lc-askoll)

The drain pump is what your washer uses to remove the water from the tub. The pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or has a burning smell, you may need to replace the drain pump. This pump has 120 volts, 60 hz and is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

Easy Part #:

EAP7783938

Availability:

In Stock

Price:

$93.12

Front lower drum seal (seal-basket lower)

This part helps to keep the dryer running as quietly as possible.

Easy Part #:

EAP460194

Availability:

In Stock

Price:

$26.87

Multi-rib drum belt (belt-dryer)

This belt helps rotate from the drive motor to the drum.

Easy Part #:

EAP3408299

Availability:

In Stock

Price:

$9.41

Door catch (catch-door)

The door catch helps keep the door closed while the machine is running. If your dryer will not start or the door will not close, you may need to replace the door catch. This is a genuine OEM part. Please remember to disconnect the power to your dryer before you start the repair.

Easy Part #:

EAP418433

Availability:

In Stock

Price:

$36.47

'm' series ignition coil kit (coil-secondary)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they will not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP470049

Availability:

In Stock

Price:

$25.20

Timer knob (knob-timer,white)

This knob accepts a D-shaped shaft.

Easy Part #:

EAP418916

Availability:

In Stock

Price:

$30.95

Ball hitch (asmy-shaft (ballhitch))

If your dryer is noisy, not starting, or is not tumbling, you may need to replace the ball hitch. This part supports the back wall of your dryer and helps reduce friction as the drum spins. The part measures 5-inch in diameter and is made from metal. It is also available as part of a kit.

Easy Part #:

EAP418736

Availability:

In Stock

Price:

$44.31

Easy Part #:

EAP1152204

Availability:

In Stock

Price:

$8.25

Water inlet valve (valve-water)

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer will not stop filling with water, is leaking, or will not fill with water, you may need to replace the water inlet valve. Please make sure to disconnect the power to your washer before you start your repair. This water inlet valve is a genuine OEM part.

Easy Part #:

EAP815509

Availability:

In Stock

Price:

$23.28

Easy Part #:

EAP12579101

Availability:

In Stock

Price:

$6.09

Front upper felt seal with adhesive (felt-upper)

The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so that heat remains in the dryer while it tumbles. If your old upper felt seal is coming apart, you notice that hot air is leaking out the dryer door, or your clothes are taking too long to dry, you may need to replace the seal. When you order this part, it comes with the upper felt seal, as well as the required high-temperature adhesive.

Easy Part #:

EAP832644

Availability:

In Stock

Price:

$17.36

1-15 of 199