58715202801 Kenmore Dishwasher Parts List

Dishwasher bottom door gasket (gasket)

This gasket goes on the bottom of the dishwasher door to create a tight seal between the tub and the outer edge of the door. If the gasket is cracked or broken, it will need to be replaced to keep water from leaking out on to the floor. The gasket is approximately 23” long and is a genuine OEM part. It is recommended that once you have installed the gasket to leave the door closed for a few hours to make sure the gasket is properly sealed.

Wheel & bushing ass (wheel bracket)

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.

Dishwasher tub gasket - gray (gasket)

The door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. This gray door gasket is made of rubber and is a genuine OEM part.

Upper spray arm (spray arm)

The upper spray arm helps distribute water from the top of the dishwasher tub. The spray arm spins on the upper support when the dishwasher is running. If the spray arm is cracked, broken, or clogged with no water coming from the spray arm, your dishes may not be cleaned properly and the upper spray arm will need to be replaced. The spray arm is 9-inch long, gray in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power and water supply to your dishwasher before starting your repair.

Silverware basket (basket)

This silverware basket has been redesigned by the manufacture. This is a one piece basket that replaces a system of three baskets that snapped together. The new basket measures 16.88" x 8", has two lids and grey in color.

Splash shield kit (tub corner gasket)

This is installed at the bottom corners of the door seal.

Dishwasher drain hose (drain hose)

The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage by carrying the drain water from the dishwasher drain pump to the kitchen sink drain. The drain hose measures 8 feet long. If your drain hose becomes damaged or cracked it will cause water to leak on the floor and you will need to replace the hose. This hose is white and black in color, made of plastic and is a genuine OEM part. Please make sure you shut off the water supply and disconnect the power to the dishwasher before starting your repair.

Upper rack assembly - t3 pro (spray arm)

Upper Rack Assembly - T3 PRO. This is the complete upper rack and the wash arm.

Tine bracket (bracket)

The tine row bracket helps to hold the tine row in place on your dish rack. If your clip is broken or cracked, you should replace it. This part measures approximately 1 1/2” long. The tine row bracket is made from plastic, is gray in color, and is a genuine OEM part. It is sold individually.

Lower spray arm support (support)

Stop clip (cap)

This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.

Door spring (spring)

Sold individually.

Friction door cable (cable)

Sold individually.

Lower dishrack assembly (rack assembly)

Wheels are included. This lower dishrack assembly comes with 8 rollers enabling it to roll in and out with ease. The dishrack is approximately 22 inches long x 20 inches wide. The dishrack holds dishes in place during the dishwashing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, the part should be replaced. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly. This part is also known as a dish rack or a dishwasher rack.

Lower spray arm support (cover)

This plastic cover and stem assembly helps hold the lower spray arm in place.