62622200 Kenmore Microwave Parts List

Light bulb - 120v 30w (microwave light bulb. The bulb operates on 120 volts and uses 30 watts.)

This 30 watt 120 volt incandescent light bulb, with a small screw base is used to light up the surface below your microwave or brighten the interior of the microwave once the door has been opened. If your light bulb is burnt out it will need to be replaced. Before you change the bulb, be sure to check that the light socket still works, as it may need to be replaced as well. Remember to disconnect the power to the microwave before you begin this repair. This is a genuine OEM part and is sold individually.

Micro switch (microwave door switch. This switch is normally open. When the microwave door is shut, the door switches close to send power to the microwave.)

The microwave primary door switch, also known as a micro switch, is normally open. When the door is shut, the door switch will close to send power to the microwave to operate. If the microwave won’t start, then the switch has failed, and the part will need to be replaced. The micro switch is in the latch board section and monitors the position of the door. This part measures 1.5” L x .75” W NOTE: Due to the high voltage capacitor in the microwave, it can retain a lethal electrical charge, even when unplugged. It is suggested to have a service technician install the part. This is a genuine OEM part. Please disconnect the power to the microwave before beginning the repair.

Door handle (handle,door)

Screws NOT included.

Glass cooking tray (glass tray)

This tray rotates in your microwave ensuring more even temperatures.

Filter,charcoal (charcoal air filter for microwave oven. 7-3/4 inches by 4-3/4 inches.)

The charcoal filter is used to remove cooking odors from that air that circulates through the vent. It measures approximately 73/4-inch by3/4-inch and is sold individually. This is a genuine OEM part.

Locker (door latch hooks)

The locker, or door latch assembly fits to the inside of the microwave door, and keeps the door closed. If the door on your microwave oven doesn’t appear to close properly, you may have a problem with the door latch assembly. This locker is made of plastic and measures 7 inches long x 2 inches wide. If either of the hooks is broken or does not have any spring tension, you may need to replace the assembly.

Holder,cook auxiliary

Damper (vent damper flap)

The vent damper is used to close off the exhaust duct when the fan is not running, to prevent outside air from entering the microwave. When the fan turns on it allows air to vent away from the microwave. The damper measures approximately 10-inch long by 3-inchwide and is a genuine OEM part.

Screw,tapping (truss head tp screw+2 cut)

Turntable assembly (glass tray support)

This turntable assembly, also known as a rotating ring, is a genuine OEM replacement part for your microwave. It is brown in color and about 10 inches in diameter. This part supports the glass turntable and keeps it in place. Replacing this part is very easy and requires no tools. Simply remove the glass tray, pop out the existing ring and replace with the new one.

Cover,stirrer fan (stirrer fan cover)

Motor, ac synchronous (turntable motor)

If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.

Diode (cable, assembly) (microwave diode assembly)

Spring (spring latch mh-630h 640c)

Shaft,turntable (glass tray coupling)