66513723K601 Kenmore Dishwasher Parts List

Rack track stop (stop)

This gray rack track stop is used for your upper dish rack track to prevent the rack from sliding off the slide rail. If your rack is falling off the track, you may need to replace the track stop. This is a genuine OEM part and is sold individually.

Dishwasher heating element (heater element)

The heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dishes are not drying or the water in the dishwasher is not getting hot you may need to replace the element. This kit includes the heater, two heater fasteners, and is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Mounting bracket

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.

Dishwasher door gasket with strike - black (gasket)

This one-piece door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking, tears, or there are gaps in your gasket, you may need to replace the door gasket. This black door gasket is made of rubber, includes a new latch strike plate for the door latch, and is a genuine OEM part.

Rinse-aid dispenser cap (rinse aid cap)

The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there could be an issue with the rinse aid cap. Check the cap and its gasket for any damage or melting. If the cap has melted or it is not sealing the dispenser properly, the part should be replaced right away. This rinse aid cap comes with the gasket, so you should discard the existing gasket and rinse aid cap at the same time. The repair is relatively straightforward, and requires no tools.

Water inlet valve (inlet valve)

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Upper dish rack roller (wheel-uper)

This assembly is the wheel and the mount for your upper dishrack. Sold individually.

Tine row

The tine row is located on the lower dishrack. The tine row can be raised or lowered to provide more room in the lower dishrack. Over time the tine row can become rusted, damaged, or lost, and will need to be replaced. The manufacturer has updated the tine row, it may look different but it will still fit like the original. This part measures approximately 19 1/2” long and is made of metal. This is a genuine OEM part and is sold individually.

Bi-metal fuse (fuse)

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse.

Circulation pump and motor (pump motor assembly)

The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.

Friction sleeve

The friction sleeve helps to reduce friction between the door hinge and the door and to keep your door quiet when it opens and closes. This part is a little over an inch long and is black in color. It is sold individually.

Chopper assembly

This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.

Detergent and rinse aid dispenser (dispenser)

This part releases the detergent and rinse aid into the dishwasher. This detergent dispenser is for dishwashers. Detergent dispenser holds the dishwasher detergent in a covered compartment. Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands during this repair.

Rubber washer (heater terminal nut)

The black heating element washer goes between the heating element and the dishwasher tub to form a seal where the element attaches to prevent water from leaking during its cycle. If the washer goes bad it will cause water to leak out on to the floor. This part is made of rubber, measures approximately 1” in diameter and is sold individually. This is a genuine OEM part.

Dishwasher drain pump (drain pump)