79093553303 Kenmore Range Parts List

Oven bake element (bake element)

The bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Front drawer glide (glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Terminal block kit (terminal block)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Infinite burner switch (universal in)

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Surface element - 8 inch - 220v (element)

The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need to replace this part if your element is not heating. It might have shorted out around the coil or the terminal block; you can test the coil to see if the burner or the switch may be at fault. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Surface element - 6 inch (element)

The standard Y-frame 6” surface element supplies heat to the cooking surface on your range and is a genuine OEM part. It has a black center medallion and looped terminal end. If your element is not heating, shorted out around the coil or if the terminal block shorted out and burnt out the contacts on the end, you may need to replace the element. Please be sure to disconnect the power to your range before starting your repair. Note: The manufacturer suggests replacing the receptacle at the same time.

Light bulb (bulb)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Oven rack

The metal chrome oven rack is a genuine OEM part. The oven rack is located inside of the oven cavity to provide a stable surface for cooking or broiling. This rack measures approximately 23” long x 16” wide and is sold individually. If your rack is rusted, damaged or missing you will need to replace the oven rack. No tools are required for this repair.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Indicator light lens (lens kit)

Probe

Note: Connector could be different than original. If so cut & splice wires together with porcelain wire nuts.

Lens

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Electronic clock/timer (clock)

This part controls the functions of your oven such as bake, broil, timed bake and the clock. The overlay or touchpad is sold separately.

Drip bowl - 8 inch (pan-blk 8" w)

This is an 8-inch drip bowl for your range or cooktop. It is made of porcelain and is black in color. Place the drip pan under your burner to catch food that may drip or spill while you cook. It is 10 inches in total diameter. Be sure to wait until drip pan and burner are cool to the touch before completing this replacement.