79095651000 Kenmore Range Parts List

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Infinite burner switch (universal in)

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Light bulb (bulb)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Indicator light lens (lens kit)

Radiant element with limiter - 1200w (r f element)

The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimeter. If the element doesn’t have continuity you will need to replace the element. If it doesn’t have continuity it is suggested to check the element switch because it could be defective and need to be replaced. This element is 1200 watts and is a genuine OEM part. The manufacturer suggests making sure the cooking element is cooled before starting the repair. Please remember to disconnect the power to the appliance before starting the repair.

Lens

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Door handle (blk dr handl)

Screws NOT included.

Broil element (element)

This broil element is found on the roof of the oven.

Main terminal block kit (block)

This terminal block kit (also called terminal boards or strips) provides a convenient means of connecting individual electrical wires. This kit includes mounting screws and hex nuts and can be used with dryers and ranges. This kit allows you to attach the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Inner oven door glass panel (oven glass)

This part is the replacement inner oven door glass for your oven. It is made of glass and is approximately 16 inches wide and 7 inches long. The oven door glass allows you to see inside the oven when the door is closed. The main reason to replace the inner oven door glass is if the old glass is cracked, broken, or missing. This part is an OEM part sourced directly from the manufacturer.

Steel washer (washer)

This washer works in conjunction with the oven door handle to secure the oven door together. The washer measures 3/4-inch x 1/4-inch, is made of metal and is sold individually. This is a genuine OEM part.

Leveling leg (level leg)

Oven probe (sensor)

Also known as a temperature sensor. This part is used to detect the temperature within the oven cavity. **The following instructions only apply if the connector piece is different than the original.** Prior to cutting the leads, please check the length of the wire you will need. 1. Cut the leads on your original sensor and the replacement sensor. Be sure to leave enough length to strip and splice the new probe and original connector together. 2. Strip the insulation, or wire cover, back approximately 1/4 inches on the new probe and original connector. 3. Twist the ends of your new probe and original connector together 4. Use a wire nut, or another high heat fastener to cover your exposed wires. 5. Install your new oven probe and re assembly your oven.

Screw (screw-8-18x1)

Sold Individually.

Light indicator - 125v (indicator lamp)