79096009603 Kenmore Range Parts List

Oven bake element (bake element)

The bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Infinite burner switch (infinite large element switch)

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Handle mounting screw (screw)

This handle mounting screw works with your oven or range, and bolts the door handle to the door. It is approximately 2 inches in length and is an OEM part sourced directly from the manufacturer. If your oven door will not close or your door handle is loose or disconnected, you may need to tighten or replace the handle mounting screw.

Light bulb (lamp)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Temperature sensor (probe)

This temperature sensor detects the temperature within the oven cavity.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Radiant surface element (surface element)

This part is the heatsource. This surface element is for ranges. Surface element supplies the heat to a cooking area on top of the range. Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.

Bottom panel (panel)

This is used as the "floor" of the oven cabinet. Note: Does not come with rivets or screws. Must be purchased locally.

Radiant element with limiter - 1200w (element)

The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimeter. If the element doesn’t have continuity you will need to replace the element. If it doesn’t have continuity it is suggested to check the element switch because it could be defective and need to be replaced. This element is 1200 watts and is a genuine OEM part. The manufacturer suggests making sure the cooking element is cooled before starting the repair. Please remember to disconnect the power to the appliance before starting the repair.

Lens

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Metal rack (rack)

This is a genuine oven rack, which works with ranges.

Drawer glide (rear door glide)

Sold Individually.

Light lens indicator (lamp lens)

Door top trim (cap)

This is the part the handle screws into for installation.

Leveling leg assy (level)

The front leveling leg is used to support and level your range. The leveling leg allows you to adjust the height of your range to make the range level. This part is just the leg, the hardware is not included and can be ordered separately. If the leveling leg breaks or can no longer be adjusted, you will need to replace it. This is a genuine OEM part and is sold individually.