79691532210 Kenmore Dryer Parts List

Dryer lint filter (dryer lint filter. This filter should be cleaned before every load to ensure proper airflow for dryer operation. If the lint filter is ripped or torn,)

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

Dryer drum belt (dryer drum drive belt. 1/4 inch wide with 4 ribs and 3 grooves.)

The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum will not turn, then you may need to replace your belt. This drive belt is 1/4-inch wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Lint screen housing (lint filter cover *manufacture has modified the part and suggests replacing the filter guide also)

This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with your clothes. This product is gray in color and is made of plastic. It is sold individually. The manufacture has modified the part and suggests replacing the filter guide also. Please see your specific model information to locate the filter guide.

Moisture sensor (dryer moisture sensor bar. If the dryer timer does not advance properly inspect the moisture sensor bars for damage which can cause the automatic dryi)

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.

High limit thermostat and thermistor kit (thermostat assembly)

The thermistor, with wire harness, helps regulate and monitor the temperature inside of the dryer. The thermistor attaches onto the blower housing. If your dryer has a short drying time or a fault code is flashing, the thermistor maybe defective and will need to be replaced. Please remember to disconnect the power to the dryer before starting the repair. This is a genuine OEM part.

Filter guide

This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are noticing marks left on your clothes, a broken lint screen guide could be to blame. The lint screen guide is approximately 13 inches wide on its straight edge. It is made of plastic and is sold individually. This is an OEM part, directly from the manufacturer.

Blower thermostat (thermostat)

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.

Gas igniter (gas dryer igniter with bracket and wire harness. This is a round spiral-style igniter. The igniter uses heat to ignite the gas in the burner assembly.)

Comes with bracket and wire harness.

High limit thermostat (dryer high limit thermostat assembly. The thermostat has reset button in center it is trips due to poor air flow such as a clogged exhaust vent.)

This part is the replacement high-limit thermostat, or simply the thermostat for your dryer. It is approximately 2 inches wide from tip to tip. The center, rectangular portion of the thermostat is approximately 1 inch in width and a little more than 1 inch in length. The thermostat is a safety device that regulates the temperature inside the dryer. If the thermostat is shorted out, your dryer may not be getting any heat, and you will need to replace it. You can test the high limit thermostat for continuity by removing it and connecting it to a multimeter. Be sure to disconnect your dryer from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Parts assembly, svc (2 pack) (dryer drum roller assembly. Includes the roller shaft and mounting clips. As the bearing in the roller wears, it self-lubricates so no grease is neede)

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Felt seal (felt seal, dryer drum)

Drive motor (dryer drum drive motor with pulley. If the dryer does not start the motor could be bad.)

This motor works with the belt to drive your dryer's drum.

Leg (dryer leveling leg)

This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer unit. Please note that this dryer leg is sold individually.

Baffle (lifter)

Cover,filter (filter cover)

This part is the replacement lint filter cover for your dryer. It is made of gray plastic and is approximately 11-1/2 inches by 1-1/4 inches. The lint filter cover fits on top of the lint filter and protects it. The main reason you would want to replace the lint filter cover is if it is cracked or broken. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.