40021 Parts List

Gasket (rear shaft seal at outer tub)

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

Locking pin (shock absorber locking pin)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Impeller and seal kit (impeller kit)

This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.

Gasket (gasket seal between the front and rear outer tubs)

Upper spray arm water supply hose (hose power shower)

This is the replacement upper spray arm water supply hose for dishwasher. It is made of white plastic and has a connector piece on each end. This hose supplies water to the upper spray arm, so it can be sprayed onto your dishes when the dishwasher is running. The main reason to replace the supply hose is if it is cracked and leaking, and the spray arm is not getting enough water. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

Detergent cup shaft and lever (shaft det cp)

Cover is not included. Must order cover separately.

Pump filter (washing machine filter and trap assembly.)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Third level spray arm (spray arm asm 3rd level)

Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack. This spray arm does not come with the screws.

Detergent cup release arm (@cam det.Cup)

This is the replacement detergent cup release arm for your dishwasher. It is made of black plastic and is sold individually. The detergent cup release arm is found on the inside of the dishwasher door, and it is the part that releases both the detergent and the rinse-aid. If the rinse-aid and detergent are not being released during the dishwasher cycle, or you notice that the release arm is cracked or damaged, then you will need to replace it. A damaged detergent cup release arm can also lead to a door latch failure on your dishwasher, and it may cause the dishwasher not to start. This is an OEM part sourced directly from the manufacturer.

Drain hose

This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.

Detergent cup cover (cover, det cup)

Door latch kit (latch asm)

This door latch kit is used for dishwashers.

Finished access panel (@access panel(white))

Armature link (@armature & link)

Clamp assembly