Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

40272 LG Washer Parts List

1-15 of 104

Washing machine drain pump (drain pump and motor assembly)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:

EAP3579318

Availability:

In Stock

Price:

$46.31

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:

EAP3527427

Availability:

In Stock

Price:

$20.15

Rear tub gasket (washing machine tub seal. If the washing machine is leaking water from above the transmission, this seal is likely damaged or worn out.)

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Easy Part #:

EAP3522855

Availability:

In Stock

Price:

$25.71

Gasket (washing machine tub seal. Located between the front outer tub and rear outer tub.)

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.

Easy Part #:

EAP3522859

Availability:

In Stock

Price:

$18.30

Door gasket (washing machine door boot gasket with drain port. If the door boot is torn, the washer will leak water. The most common cause of a torn door boot is i)

Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore and Kenmore Elite 796; and LG WM and CW. Door boot 4986ER0004F forms a seal between the wash tub and the door, preventing leaks. This door boot includes a drain port; if your 27-inch LG front-load washer was made before September 2007, use door boot 4986ER0004B instead, because those washers don't have a drain port.

Easy Part #:

EAP3524977

Availability:

In Stock

Price:

$49.97

Easy Part #:

EAP3533609

Availability:

In Stock

Price:

$52.91

Spider

This part is called a spider, spinner support or rear drum support for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub while the washer is running. If you notice that your washer shakes or moves during operation, or if it is excessively noisy, you may need to replace the spider. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Easy Part #:

EAP11759952

Availability:

In Stock

Price:

$155.93

Detergent dispenser (box assembly, liquid detergent)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Easy Part #:

EAP3522644

Availability:

In Stock

Price:

$17.81

Sensor assembly (washing machine rotor position sensor assembly. This part is also called a hall sensor or motor sensor. When this part fails the control may display a)

The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code on your control display, the sensor has failed and will need to be replaced. This is a genuine OEM part sourced directly from the manufacturer. Please remember to disconnect the power to your washer before starting your repair.

Easy Part #:

EAP16556422

Availability:

In Stock

Price:

$36.50

Easy Part #:

EAP3523345

Availability:

In Stock

Price:

$37.66

Rotor assembly (washing machine rotor assembly. The rotor interacts with the stator to create a strong electromagnetic field which rotates the tub in either direction)

This rotor assembly is a manufacturer-approved replacement part for your washing machine. The rotor is an important part to rotate the tub during the wash cycle. It can need replacing if the magnets or splines become damaged. Unplug the washer before beginning this repair. To complete this repair, you will need a Phillips screwdriver, a 17mm socket wrench, and thread-locking fluid.

Easy Part #:

EAP3522944

Availability:

In Stock

Price:

$155.93

Shock absorber kit (shock absorber with two mounting pins)

This kit includes 1 shock absorber and 2 mounting pins.

Easy Part #:

EAP3522315

Availability:

No Longer Available

Inlet valve assembly

This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.

Easy Part #:

EAP3527452

Availability:

In Stock

Price:

$88.58

Washer hose with bellows (bellows)

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Easy Part #:

EAP3523347

Availability:

In Stock

Price:

$23.95

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Easy Part #:

EAP7788210

Availability:

In Stock

Price:

$9.98

1-15 of 104