Parts for Kenmore Models DDG5180RBL

M series new style coil kit

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $26.40

D-shaped knob clip (u clip)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Easy Part #:: EAP268493

Availability:: No Longer Available

Rear drum bearing kit (shaft & bracket asm)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP267529

Availability:: In Stock

Price:: $62.96

Drive belt (belt drive)

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Easy Part #:: EAP2350043

Availability:: In Stock

Price:: $25.19

Idler pulley wheel (pulley idler)

The idler pulley helps maintain the proper amount of tension on the drive belt to turn the drum. The idler pulley is located between the motor pulley and drum to provide tension on the belt. If the part has become worn, it could cause the dryer to be noisy or squeaky, and the pulley will need to be replaced. This part is yellow in color, made of plastic, and measures approximately 2 1/2” in diameter. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP265721

Availability:: In Stock

Price:: $28.58

Lint filter with frame (filter asm lint)

The lint filter and frame for your dryer traps unwanted lint and debris so your dryer can effectively dry your clothes. If the old lint filter is cracked or clogged, or the dryer takes too long to dry or if excessive lint is accumulating inside the dryer or its venting, you may need to replace the lint filter. To replace the filter, simply remove the old, damaged filter, and replace it with the new one. This part is approximately 13 inches by 3 inches.

Easy Part #:: EAP266250

Availability:: No Longer Available

Door latch (latch door)

This part helps to keep the door closed while the machine is running.

Easy Part #:: EAP3502777

Availability:: In Stock

Price:: $14.53

Rear drum bearing (bearing drum shaft)

This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.

Easy Part #:: EAP267865

Availability:: In Stock

Price:: $17.17

Front drum slide kit (slide asm)

This front drum slide kit comes with two slides with the apppropriate mounting hardware.

Easy Part #:: EAP267600

Availability:: No Longer Available

Gas igniter (igniter)

Be very careful to not handle the igniter by its gray part. Hold it by its white tip only.

Easy Part #:: EAP268028

Availability:: In Stock

Price:: $35.69

M-series primary dual coil gas valve (coil dual)

This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.

Easy Part #:: EAP268153

Availability:: In Stock

Price:: $31.37

Adjustable leveling screw (screw levelling 5/16-24)

The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able to create a level base for your dryer. The leveling screw has a hexagon-shaped gray plastic foot, with a screw that is approximately 1 inch in length. To replace a damaged screw, simply turn the old screw to the left, until it can be removed. Then, simply screw the new leveling screw into place on the bottom of the dryer, making sure it is the same height as the other 3 leveling screws.

Easy Part #:: EAP1021358

Availability:: In Stock

Price:: $13.36

M - series secondary coil - 2 terminals

This part is the replacement main valve coil for your dryer. It is black and white in color and has 2 terminals. It is approximately 1 inch long and 1 inch wide. The main valve coil opens the gas valves while the dryer is running. This coil is used with two coil gas shut off valve assemblies. Be sure to turn off the gas before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

Easy Part #:: EAP268154

Availability:: In Stock

Price:: $27.52

Rotary start switch (switch rotary start)

This is the replacement rotary start switch for your dryer. It is silver and black in color, with a white D-shaped shaft. The rotary start switch is found inside the dryer control panel, and when actuated, it starts the dryer. Over time, the contacts inside the switch can short out, and when this happens, the dryer will not start. As you will be working around electricity, be sure to disconnect the dryer from the power source before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Easy Part #:: EAP268227

Availability:: In Stock

Price:: $43.70

Drive motor (switch-start form j mtr.)

Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.