DDW650B-55 Parts List

Sump housing (dishwasher sump housing)

This part is the replacement sump housing or sump insert for your dishwasher. It is made of plastic and is approximately 7 inches by 5 inches. The sump housing is attached to the bottom of the dishwasher tub and collects water for the pump. If your dishwasher is leaking, you may need to replace the sump housing. Be sure to disconnect the dishwasher from the water and power source before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Water inlet valve (dishwasher water inlet valve)

This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Impeller and seal kit (motor shaft seal and impeller kit)

This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.

Upper spray arm water supply hose (water supply hose, upper spray)

This is the replacement upper spray arm water supply hose for dishwasher. It is made of white plastic and has a connector piece on each end. This hose supplies water to the upper spray arm, so it can be sprayed onto your dishes when the dishwasher is running. The main reason to replace the supply hose is if it is cracked and leaking, and the spray arm is not getting enough water. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

Detergent cup shaft and lever (shaft and lever for soap cup)

Cover is not included. Must order cover separately.

Detergent cup release arm

This is the replacement detergent cup release arm for your dishwasher. It is made of black plastic and is sold individually. The detergent cup release arm is found on the inside of the dishwasher door, and it is the part that releases both the detergent and the rinse-aid. If the rinse-aid and detergent are not being released during the dishwasher cycle, or you notice that the release arm is cracked or damaged, then you will need to replace it. A damaged detergent cup release arm can also lead to a door latch failure on your dishwasher, and it may cause the dishwasher not to start. This is an OEM part sourced directly from the manufacturer.

Drain hose

This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.

Detergent cup cover

Armature link (plunger and armature, drain solenoid)

Drain solenoid repair kit

This kit includes the armature and link assembly. You may need the solenoid bracket which is sold separately. This valve opens in order for the water to drain out of the dishwasher.

Detergent cup door spring (detergent door trip spring)

Hose clamp kit

This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.

Screw

Size: 10-16 ab. * Part may differ in appearance, but functions same as original. Sold Individually.

Valve body gasket (gasket valve body)

Rinse aid injector container with gasket (tank rinse aid kit)

This part attaches to the inner door panel.