DSS25KGTB GE Refrigerator Parts List

Ice bucket and auger assembly (bucket and auger asm)

This part holds the ice once it's released from the icemaker. When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

Middle pan cover frame - no glass (cover middle pan)

This is the frame only. Glass is NOT included and must order separately.

Middle crisper pan (pan middle asm)

Fruits and vegetable drawer.

Compression ring (ring compression)

The compression ring works for a variety of fans throughout your refrigerator, the evaporator fan or condenser fan. If you notice your refrigerator or freezer is too warm, or there is an unusual sound during operation you may need to replace the compression ring. This part is made of metal, measures approximately 0.25” L x 0.5” in diameter, and is sold individually. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Lid bumper (bumper lid)

This orange rubber bumper prevents the condenser fan motor from bumping against the mounting bracket every time the fan motor starts. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. It has a rounded top and a slightly pointed bottom. The bumper is a genuine OEM part and is sold individually.

Light switch (switch light)

This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simply use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.

Water tank assembly (water tank disp asm)

This tank stores water until the water actuator is activated and water is requested.

Union connector - 5/16 inch to 5/16 inch (quick connector for refrigerator water line, 5/16 to 5/16 inches.)

Quick connector for plastic water line - 5/16" to 5/16"

Run capacitor (refrigerator run capacitor 12 uf. If this run capacitor is defective, the refrigerator will not run.)

The run capacitor is attached to the compressor and is 12 UF. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Shelf stop - white (stop shelf)

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

Dispenser door recess crank (crank door recess)

The door recess crank for your refrigerator is located inside the water dispenser assembly. To access this part, you will need to take apart the dispenser assembly. To do this, you will need a putty knife and a Phillips screwdriver. If your dispenser door will not close properly, or ice is not dispensing properly, you may have a damaged door recess crank. This part is made of white plastic and is sold individually.

Light bulb - 40w (lamp 60w appl)

This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.

Wheel pan cover

Pan cover glass (glass pan covr)

Glass only. Frame sold separately.

Bottom pan cover (cover top meat)

Also known as Chill Cover.