Parts for Kenmore Models EE2107

M series new style coil kit (dryer valve coil kit)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $26.40

Drum support roller (dryer drum support roller. The rollers tend to wear at the same rate so both should be replaced while the dryer is apart.)

This single drum support roller is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. It is sold individually.

Easy Part #:: EAP11741913

Availability:: In Stock

Price:: $19.49

Multi rib belt (dryer drum drive belt. Length 93 3/8”, width 3/8”, characteristics, 5 ridges, flat.)

This dryer drum belt has five ridges, 93-3/8 inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP11742271

Availability:: In Stock

Price:: $11.49

Thrust washer (laundry appliance washer)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock

Price:: $7.40

Idler pulley wheel with bearing (idler pulley wheel and bearing assembly. The idler pulley puts tension on the drive belt. If the idler pulley fails to put the proper amount of tensio)

This two-inch-wide idler pulley wheel is black in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center. This part helps maintains the correct tension on the drive belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11757553

Availability:: In Stock

Price:: $18.60

Dryer idler assembly (dryer idler pulley assembly. If the dryer drum does not turn check if the idler pulley is rotating freely and putting.)

The spring for this part is sold separately. This idler assembly is for dryers. Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the belt to turn. Disconnect the power before installing this part. Wear work gloves to protect your hands.

Easy Part #:: EAP11741930

Availability:: In Stock

Price:: $33.20

Single drum glide felt pad (felt pad)

This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.

Easy Part #:: EAP11742773

Availability:: In Stock

Price:: $6.43

Retaining ring (laundry appliance retaining ring)

The retaining clip goes onto the end of the roller axle and holds the rear wheel onto the axle. If the ring is broken, damaged, making noises, or will not tumble, you will need to replace it. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11740487

Availability:: In Stock

Price:: $12.64

Screw, 8/18 x 3/8 (screw)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $7.40

Cylinder felt seal (dryer drum felt seal)

The felt seal keeps the hot air in the dryer drum. It is located between the back of the drum and the rear dryer panel. If your dryer is noisy, or the seal is damaged, you will need to replace it. This is the seal only; the high temperature adhesive is not included. This is a genuine OEM part. Please make sure you disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP11741917

Availability:: In Stock

Price:: $35.06

Door switch kit (dryer door switch)

This part replaces older two terminal switches.

Easy Part #:: EAP1964648

Availability:: In Stock

Price:: $13.63

Door latch kit (dryer door catch kit. Includes door catch and clip (plastic))

This dryer door latch kit comes in two pieces: a door latch, and a door strike. It's used to help hold your door shut to your dryer.

Easy Part #:: EAP2029855

Availability:: In Stock

Price:: $11.43

Limit thermostat (high limit thermostat, l225-40f)

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 225 degrees Fahrenheit. The element will kick back in when the temperature drops to 185 degrees Fahrenheit - the differential of 40 degrees.

Easy Part #:: EAP11748479

Availability:: In Stock

Price:: $54.47

Spring retaining clip (speed clip)

This spring retaining clip is used to hold the front panel onto the top of the washer. If your front panel is loose you might need to replace the clip. The clip is made entirely of metal and is used for some washing machines. This part is not quite an inch long and is sold individually. This is a genuine OEM part.