F10A4FNP LG Washer Parts List

Washing machine drain pump (washing machine drain pump. If the washer does not drain then the drain pump may be clogged, damaged, or defective.)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Rear tub gasket (washing machine tub seal. If the washing machine is leaking water from above the transmission, this seal is likely damaged or worn out.)

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Door gasket (washing machine door boot gasket with drain port. If the door boot is torn, the washer will leak water. The most common cause of a torn door boot is i)

Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore and Kenmore Elite 796; and LG WM and CW. Door boot 4986ER0004F forms a seal between the wash tub and the door, preventing leaks. This door boot includes a drain port; if your 27-inch LG front-load washer was made before September 2007, use door boot 4986ER0004B instead, because those washers don't have a drain port.

Door lock assembly (washer door lock latch assembly. The door lock secures the washer door shut during operation. Once the washing machine door is closed, the washer can)

Detergent dispenser (box assembly, liquid detergent)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Tub-to-pump drain hose (washing machine drain hose with bellows. This drain hose makes a connection from the washer tub to the drain pump.)

This hose has bellows to allow for flexibility during the wash and spin cycles.

Washer hose with bellows (bellows)

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Clamp assembly

Rotor assembly (washing machine rotor assembly. The rotor interacts with the stator to create a strong electromagnetic field which rotates the tub in either direction)

Hose (bellows)

Stator assembly (washing machine stator assembly with sensor.)

Switch assembly, pressure (water level pressure switch)

Locker,hook

Hinge assembly