GDP615HYN0FS GE Dishwasher Parts List

Basket asm silverware

This basket is part of a silverware basket that has 3 sections. This is the middle section of the basket.

Lower dishrack with wheels (rack lower asm complete)

Note: This "Service Rack" fits numerous models. Per factory, on some models, it may be necessary to move the silverware basket to the inside of the rack along the right side.

Countertop bracket (bracket countertop)

This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the cabinet or countertop. This part is about 3 inches long and is made of metal. This kit does not include the screws, please order screws separately if necessary.

Door latch (latch tub side standard)

This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a broken or faulty door latch, your dishwasher door may not stay closed, and this can prevent the dishwasher from running. This item is sold individually, and if your door strike is also damaged, you will need to replace that part separately. This is an OEM part sourced directly from the manufacturer.

End cap

This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuously falls off the track or rail.

Dishwasher tub gasket (gasket tub plastic)

The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the floor after you run your dishwasher, it may be an indication that the gasket is loose or damaged. If your door gasket is damaged, it will need to be replaced. To replace the gasket, simply pull the old gasket out of the groove it rests in, and press the new gasket into place. This part is made of black rubber and is sold individually.

Water valve and harness service asm (valve water asm)

This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the appliance is not in use, you may need to replace the inlet valve. It measures approximately 3 inches by 4 inches and is made of metal and white plastic.

Screw 8-16 hxw 1/2 stainless steel (screw 8-16 hxw 1/2 ss)

Sold Individually.

Lower spray arm (arm spray lower asm)

Detergent module (detergent disp no sensor)

The detergent dispenser in your dishwasher stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end of the cycle, you may have a damaged or malfunctioning detergent dispenser. This detergent dispenser is not sold with a sensor. It is gray in color and is sold individually. This is an OEM part sourced directly from the manufacturer.

Door cable (cable asm pulley)

This part is the replacement door hinge cable for your dishwasher. The door hinge cable connects the door spring to the door hinge, and allows the door to drop down slowly when it is opened. If you open your dishwasher and the door drops down quickly, your door hinge cable may need to be replaced. Be sure to disconnect the water and power sources from the dishwasher before you begin this repair. The door hinge cable is sold individually.

Rack carrier kit - right or left side (cover roller lh)

This part is the replacement carrier roller for your dishwasher. It is also known as the wheel support. It is made of gray plastic and is approximately 5 inches by 2 inches. The carrier roller supports the wheels on your upper dish rack so it can slide in and out of the dishwasher efficiently. This part has been redesigned by the manufacturer. This part can now be used on the right or left side of the rack. Because it is made of plastic, the roller can occasionally crack and break, and when this occurs, it will need to be replaced. If you notice that your dish rack is having difficulty sliding in and out, you should check to see if the roller is damaged. This is an OEM part from the manufacturer and it is sold individually. The roller itself, is replacement part number WD12X26146. The cover is no longer needed when replacing the rack carrier kit.

Diverter assembly kit (diverter passive main as)

Drain pump kit (drain pump asm)

Circulation pump (pump wash main asm)

This part contains the Piranha clamps in kit WD35X10382